Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am571x-idk.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM572x IDK and AM571x IDK boards have equivalent
design of how SD card and eMMC are connected.
The two EVMs mainly differ in IOdelay configuration
needed (because of difference in SoC used).
Move the common properties to am57xx-idk-common.dtsi
file which is common for both EVMs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am57xx-beagle-x15/am57xx-beagle-x15-revb1.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra7-evm.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinmux configuration for MMC module including IODELAY
values suggested in the data manual for the various supported
modes.
IOdelay data for both silicon revision 1.1 and 2.0 is
added here.
The datamanual revisions used are:
* AM572x Silicon Revision 2.0: SPRS953B, Revised November 2016
* AM572x Silicon Revision 1.1: SPRS915R, Revised November 2016
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinmux configuration for MMC module including IODELAY
values suggested in the data manual for the various supported
modes.
IOdelay data for both silicon revision 1.0 and 2.0 is
added here.
The datamanual revisions used are:
* AM571x Silicon Revision 2.0: SPRS957D, Revised January 2017
* AM571x Silicon Revision 1.0: SPRS919M, Revised November 2017
* DRA71x : SPRS960B, Revised February 2017
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add camera support to N900 dts. Also add a note about MMC & debugging.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dra76-evm is a board based on TI's dra76 processor targeting
for infotainment systems. Adding support for this platform.
dra76-evm and dra7-evm has a similar layout except with few differences.
So create a dra7-evm-common.dtsi with similarities on dra76-evm and
dra7-evm. Include this common dtsi in both dra7-evm.dts and dra76-evm.dts
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dra76 family is a high-performance, infotainment application
device, based on OMAP architecture on a 28-nm technology.
This contains most of the subsystems, peripherals that are
available on dra74, dra72 family. This SoC mainly features
Subsystems:
- 2 x Cortex-A15 with max speed of 1.8GHz
- 2 X DSP
- 2 X Cortex-M4 IPU
- ISS
- CAL
- DSS
- VPE
- VIP
Connectivity peripherals:
- 1 USB3.0 and 3 USB2.0 subsystems
- 2 x SATA
- 2 x PCI Express Gen2
- 3-port Gigabit ethernet switch
- 2 x CAN
- MCAN
Adding basic dts support for DRA76 family while reusing the
data available in dra7.dtsi, dra74x.dtsi.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pcie1 dt node in order for the controller to operate in
endpoint mode. However since none of the dra7 based boards have
slots configured to operate in endpoint mode, keep EP mode
disabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for Moxa UC-8100-ME-T open platform
The UC-8100-ME-T computing platform is designed
for embedded data acquisition industrial applications
The features of UC-8100-ME-T series are:
* eMMC
* SPI flash
* SD slot
* 2x LAN
* 2 RS-232/422/485 ports, software-selectable
* Mini PCIe form factor with USB signal
* USB host
* EEPROM
* TPM
* Watchdog
* RTC
* User gpio-keys
* User LEDs
* User button
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Acked-by: Rob Herring <robh@kernel.org>
[tony@atomide.com: fix unit adress as suggested by Rob]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the default method of prefetch polled shows the highest
possible read and write speed when minimal non NAND background
activity is being done. But it is also very CPU intensive to reach
these high speeds (CPU load of 99% via mtd performance tests). While
DMA prefetch only uses 50% of the CPU to achieve around 23% less in
top read and write performance.
However, as the non NAND CPU load increases the read and write
performance takes a large hit when using polled prefetch. Therefore,
prefetch dma mode ends up outperforming prefetch polled in general
"system level" test. So switch to using dma prefetch by default since
it is likely what most users would prefer.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the default method of prefetch polled shows the highest
possible read and write speed when minimal non NAND background
activity is being done. But it is also very CPU intensive to reach
these high speeds (CPU load of 99% via mtd performance tests). While
DMA prefetch only uses 50% of the CPU to achieve around 23% less in
top read and write performance.
However, as the non NAND CPU load increases the read and write
performance takes a large hit when using polled prefetch. Therefore,
prefetch dma mode ends up outperforming prefetch polled in general
"system level" test. So switch to using dma prefetch by default since
it is likely what most users would prefer.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the default method of prefetch polled shows the highest
possible read and write speed when minimal non NAND background
activity is being done. But it is also very CPU intensive to reach
these high speeds (CPU load of 99% via mtd performance tests). While
DMA prefetch only uses 50% of the CPU to achieve around 23% less in
top read and write performance.
However, as the non NAND CPU load increases the read and write
performance takes a large hit when using polled prefetch. Therefore,
prefetch dma mode ends up outperforming prefetch polled in general
"system level" test. So switch to using dma prefetch by default since
it is likely what most users would prefer.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Set default mode for vaudio, which may be left in standby mode
if the system is booted via kexec from Android.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All nodes inhert "interrupt-parent" property from root
node. Removed the aforementioned property from usbhsohci,
usbhsehci, ssi_port1, ssi_port2 nodes to avoid duplication.
Signed-off-by: Karthik Tummala <karthik@techveda.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Devices using an external encoder, ESD protection and level shifter
such as tpd12s015 or ip4791cz12 have the CEC pull in the encoder
chip. And on var-som-om44, there is external pull up resistor R30.
So the internal CEC pull-up resistor needs to be disabled as otherwise
the external and internal pull are parallel making the pull value
much smaller than intended. This leads into the CEC not working as
reported by Hans Verkuil <hverkuil@xs4all.nl>.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for onboard gpio buzzer. It works using
the gpio-beeper driver. Pinmux entries for GPIO
controlling the buzzer are also added.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The interrupt for power button is static data that comes from the
datasheet, there is no reason to need to define this value on every
board so seams reasonable put this information into the common tps65217
file.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The interrupt specifiers for USB and AC charger input are static data that
comes from the datasheet, there is no reason to need to define these values
on every board so seem reasonable put this information into the common
tps65217 file.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace deprecated "vmmc_aux" with the generic "vqmmc" binding for
MMC IO supply.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPIO polarity for MMC1 card detect is set to '0' which means
active-high. However the polarity should be active-low. Fix it
here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPIO polarity for MMC1 card detect is set to '0' which means
active-high. However the polarity should be active-low. Fix it
here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull ARM device-tree updates from Arnd Bergmann:
"Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
New machines:
- The new Action Semi S500 platform is added along with initial
support for the LeMaker Guitar board.
- STM32 gains support for three new boards: stm32h743-disco,
stm32f746-disco, and stm32f769-disco, along with new device support
for the existing stm32f429 boards.
- Renesas adds two new boards, the tiny GR-Peach based on RZ/A1H with
10MB on-chip SRAM, and the iWave G20D-Q7 System-on-Module plus
board.
- On Marvell "mvebu", we gain support for the Linksys WRT3200ACM
wireless router.
- For NXP i.MX, we gain support for the Gateworks Ventana GW5600 and
the Technexion Pico i.MX7D single-board computers.
- The BeagleBone Blue is added for OMAP, it's the latest variation of
the popular Beaglebone Black single-board computer.
- The Allwinner based Lichee Pi Zero and NanoPi M1 Plus boards are
added, these are the latest variations of a seemingly endless
supply of similar single-board computers.
Other updates:
- Linus Walleij improves support for the "Faraday" based SoC
platforms from various SoC makers (Moxart, Aspeed, Gemini)
- The ARM Mali GPU is now describe on Rockchips SoCs
- Mediatek MT7623 is extended significantly, making it much more
useful.
- Lots of individual updates on Renesas, OMAP, Rockchips, Broadcom,
Allwinner, Qualcomm, iMX
- For Amlogic, the clock support is extended a lot on meson8b.
- We now build the devicetree file for the Raspberry Pi 3 on 32-bit
ARM, in addition to the existing ARM64 support, to help users
wanting to run a 32-bit system on it"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (345 commits)
ARM: dts: socfpga: set the i2c frequency
ARM: dts: socfpga: Add second ethernet alias to VINING FPGA
ARM: dts: socfpga: Drop LED node from VINING FPGA
ARM: dts: socfpga: Remove I2C EEPROMs from VINING FPGA
ARM: dts: socfpga: Enable QSPI support on VINING FPGA
ARM: dts: socfpga: Fix the ethernet clock phandle
ARM: pxa: Use - instead of @ for DT OPP entries
ARM: dts: owl-s500: Add SPS node
ARM: dts: owl-s500: Set CPU enable-method
dt-bindings: arm: cpus: Add S500 enable-method
ARM: dts: Add Actions Semi S500 and LeMaker Guitar
dt-bindings: arm: Document Actions Semi S900
dt-bindings: timer: Document Owl timer
ARM: dts: imx6q-cm-fx6: add sdio wifi/bt nodes
dt-bindings: arm: Document Actions Semi S500
dt-bindings: Add vendor prefix for Actions Semi
ARM: dts: turris-omnia: Add generic compatible string for I2C EEPROM
ARM: dts: mvebu: add support for Linksys WRT3200ACM (Rango)
ARM: dts: armada-385-linksys: fixup button node names
ARM: dts: armada-385-linksys: group pins in pinctrl
...
Pull non-urgent ARM SoC fixes from Arnd Bergmann:
"Smaller patches that didn't seem to find a home in other branches, and
low-priority fixes from late in the merge window.
- Lee Jones retires as bcm2835 (raspberry pi) co-maintainer.
- a couple of bugfixes for the ARM CCN bus driver that were regarded
not important enough
- minor device tree fixes for the Renesas and Marvell platforms, that
came a little late or did not justify have another pull request
after the last -rc"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
bus: arm-ccn: Enable stats for CCN-502 interconnect
dt-bindings: arm-ccn: Add bindings info for CCN-502 compatible string
bus: arm-ccn: Use devm_kcalloc() in arm_ccn_probe()
bus: arm-ccn: Fix module autoload
MAINTAINERS: add RV1108 Rockchip soc to maintained files
ARM: dts: kirkwood: Fix Openblock A6 nand partition overlap
ARM: dts: armadillo800eva: Split LCD mux and gpio
MAINTAINERS: Remove Lee Jones from bcm2835.
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support to enable irq wake for slot gpio
- Remove MMC_CAP2_HC_ERASE_SZ and make it the default behaviour
- Improve R1 response error checks for stop commands
- Cleanup and clarify some MMC specific code
- Keep card runtime resumed while adding SDIO function devices
- Use device_property_read instead of of_property_read in mmc_of_parse()
- Move boot partition locking into a driver op to enable proper I/O scheduling
- Move multi/single-ioctl() to use block layer to enable proper I/O scheduling
- Delete bounce buffer Kconfig option
- Improve the eMMC HW reset support provided via the eMMC pwrseq
- Add host API to manage SDIO IRQs from a workqueue
MMC host:
- dw_mmc: Drop support for multiple slots
- dw_mmc: Use device_property_read instead of of_property_read
- dw_mmc-rockchip: Optional improved tuning to greatly decrease tuning time
- dw_mmc: Prevent rpm suspend for SDIO IRQs instead of always for SDIO cards
- dw_mmc: Convert to use MMC_CAP2_SDIO_IRQ_NOTHREAD for SDIO IRQs
- omap_hsmmc: Convert to mmc regulator APIs to consolidate code
- omap_hsmmc: Deprecate "vmmc_aux" in DT and use "vqmmc" instead
- tmio: make sure SDIO gets reinitialized after resume
- sdhi: add CMD23 support to R-Car Gen2 & Gen3
- tmio: add CMD23 support
- sdhi/tmio: Refactor code and rename files to simplify Kconfig options
- sdhci-pci: Enable card detect wake for Intel BYT-related SD controllers
- sdhci-pci: Add support for Intel CNP
- sdhci-esdhc-imx: Remove ENGcm07207 workaround - allow multi block transfers
- sdhci-esdhc-imx: Allow all supported prescaler values
- sdhci-esdhc-imx: Fix DAT line software reset
- sdhci-esdhc: Add SDHCI_QUIRK_32BIT_DMA_ADDR
- atmel-mci: Drop AVR32 support"
* tag 'mmc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (86 commits)
mmc: dw_mmc: remove the unnecessary slot variable
mmc: dw_mmc: use the 'slot' instead of 'cur_slot'
mmc: dw_mmc: remove the 'id' arguments about functions relevant to slot
mmc: dw_mmc: change the array of slots
mmc: dw_mmc: remove the loop about finding slots
mmc: dw_mmc: deprecated the "num-slots" property
mmc: dw_mmc-rockchip: parse rockchip, desired-num-phases from DT
dt-bindings: rockchip-dw-mshc: add optional rockchip, desired-num-phases
mmc: renesas-sdhi: improve checkpatch cleanness
mmc: tmio: improve checkpatch cleanness
mmc: sdhci-pci: Enable card detect wake for Intel BYT-related SD controllers
mmc: slot-gpio: Add support to enable irq wake on cd_irq
mmc: core: Remove MMC_CAP2_HC_ERASE_SZ
mmc: core: for data errors, take response of stop cmd into account
mmc: core: check also R1 response for stop commands
mmc: core: Clarify code for sending CSD
mmc: core: Drop mmc_all_send_cid() and use mmc_send_cxd_native() instead
mmc: core: Re-factor code for sending CID
mmc: core: Remove redundant code in mmc_send_cid()
mmc: core: Make mmc_can_reset() static
...
Pull "Actions Semi ARM based SoC DT for v4.13" from Andreas Färber:
This adds an initial DT for the S500 SoC and a devboard based on it.
* tag 'actions-arm-dt-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions:
ARM: dts: owl-s500: Add SPS node
ARM: dts: owl-s500: Set CPU enable-method
dt-bindings: arm: cpus: Add S500 enable-method
ARM: dts: Add Actions Semi S500 and LeMaker Guitar
dt-bindings: arm: Document Actions Semi S900
dt-bindings: timer: Document Owl timer
dt-bindings: arm: Document Actions Semi S500
dt-bindings: Add vendor prefix for Actions Semi
Merge "Amlogic 32-bit DT changes for v4.13 (round 2)" from Kevin Hilman:
- greatly expands DT clock support for meson8b
* tag 'amlogic-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: (22 commits)
ARM: dts: meson: use the real ethernet clock on Meson8 and Meson8b
ARM: dts: meson8b: add the SCU device node
ARM: dts: meson: add USB support on Meson8 and Meson8b
ARM: dts: meson: add the hardware random number generator
ARM: dts: meson8: add reserved memory zones
ARM: dts: meson: add the SAR ADC
ARM: dts: meson8: add the pins for the SDIO controller
ARM: dts: meson8: add the PWM_E and PWM_F pins
ARM: dts: meson: use GIC_SPI and IRQ_TYPE_EDGE_RISING macros
ARM: dts: meson: use C preprocessor friendly include syntax
ARM: dts: meson8: fix the IR receiver pins
clk: meson8b: export the ethernet gate clock
clk: meson8b: export the USB clocks
clk: meson8b: export the gate clock for the HW random number generator
clk: meson8b: export the SDIO clock
clk: meson8b: export the SAR ADC clocks
clk: meson-gxbb: un-export the CPU clock
clk: meson-gxbb: expose UART clocks
clk: meson-gxbb: expose SPICC gate
clk: meson-gxbb: expose spdif master clock
...
Pull "SoCFPGA DTS updates for v4.13" from Dinh Nguyen:
- Fix clocks node the EMACs
- VINING board updtes
- Remove I2C EEPROMs and LED node
- Add QSPI device
- Add 2nd ethernet alias
- Add 'clock-frequency' binding for i2c node
* tag 'socfpga_dts_for_v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: set the i2c frequency
ARM: dts: socfpga: Add second ethernet alias to VINING FPGA
ARM: dts: socfpga: Drop LED node from VINING FPGA
ARM: dts: socfpga: Remove I2C EEPROMs from VINING FPGA
ARM: dts: socfpga: Enable QSPI support on VINING FPGA
ARM: dts: socfpga: Fix the ethernet clock phandle
Use 'clock-frequency' binding for the i2c node that will put the I2C driver
into the standard operating mode. 'speed-mode' was not a valid binding for
the I2C driver, remove it.
Signed-off-by: Alan Tull <atull@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add DT alias for the second ethernet present on mainboard rev 1.10.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Drop the LED node from VINing FPGA DT because the LED wiring is
different on each mainboard revision. This wiring is therefore
handled in mainboard DT Overlays.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Remove the EEPROMs attached to the I2C expander ports which
lead to the backplane slots from the main VIN|ING DTS file.
These EEPROMs are bound using separate DTO files, which lets
us handle both two-slot and six-slot configuration of the
backplane.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The ethernet block clock phandle must point to the clock node which
represents the clock which directly supply the ethernet block. This
is emac_x_clk , not emacx_clk , so fix this.
From: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Pull "pxa-dt for v4.13" from Robert Jarzmik:
This device-tree pxa update brings :
- cpu operating points renaming from Viresh
* tag 'pxa-dt-4.13' of https://github.com/rjarzmik/linux:
ARM: pxa: Use - instead of @ for DT OPP entries
Pull "Samsung DeviceTree update for v4.13, part two" from Krzysztof Kozłowski:
1. Add needed property for CEC on Odroid U3,
2. Fix reset GPIO polarity on Rinato.
* tag 'samsung-dt-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Fix polarity of panel reset gpio in Rinato
ARM: dts: exynos: add needs-hpd to &hdmicec for Odroid-U3
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
commit 94647a3012 ("ARM: dts: omap3-overo: Enable WiFi/BT combo")
while enabling WiFi/BT combo added regulator to trigger the nReset
signal of the Bluetooth module in vqmmc-supply. However BT should be
handled by UART. Moreover "vqmmc" is not a defined binding for
omap_hsmmc. While "vqmmc" in mmc2 hasn't caused any issues so far,
mmc2 will start to mis-behave once omap_hsmmc defines "vqmmc"
binding.
Remove "vqmmc-supply" property in mmc2 here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add "max-frequency" property to MMC dt nodes and set the
maximum frequency to 192MHz for MMC1/MMC2, 64MHz for MMC3
and 192MHz for MMC4. pdata quirks must be utilized to
detect presence of rev 1.1/1.0 of silicon and adjust
maximum frequencies as per restrictions documented in i843.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On DRA75x EVM, MMC2 vdd/ios are connected to a common supply fixed at 1.8V
not 3.3V
Fixes: 6cf02dbb4b ("ARM: dts: dra7-evm: Add mmc2 node for eMMC support")
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The dt binding documentation of omap-hsmmc recommends using
"vmmc_aux" for IO supply lines. However
commit 0af28cc926 ("ARM: dts: am57xx-beagle-x15: Add support
for rev B1") added it as "vmmc-aux". Now that anyways it
needs to be fixed, use the generic "vqmmc" binding instead of
the deprecated "vmmc_aux".
Fixes: commit 0af28cc926 ("ARM: dts: am57xx-beagle-x15: Add
support for rev B1")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
