Using coherent DMA memory with the OMAP DMA engine results in
unpredictable behaviour due to memory ordering issues; as things stand,
there is no guarantee that data written to coherent DMA memory will be
visible to the DMA hardware.
This is because the OMAP dma_write() accessor contains no barriers,
necessary on ARMv6 and above. The effect of this can be seen in comments
in the OMAP serial driver, which incorrectly talks about cache flushing
for the coherent DMA stuff.
Rather than adding barriers to the accessors, add it in the DMA support
code just before we enable DMA, and just after we disable DMA. This
avoids having barriers for every DMA register access.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MMCI driver will not work without two IRQs since this is not
flagged as a single-irq variant. Looking through the complex IRQ
definition for the MMCI on the versatile (including an #if 1
statement forcing MMCI IRQ0 to the VIC) this appears to the the
correct IRQ number for both models.
Cc: Niklas Hernaeus <niklas.hernaeus@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM PCS mandates that the length and stride bits of the fpscr are
cleared on entry to and return from a public interface. Although signal
handlers run asynchronously with respect to the interrupted function,
the handler itself expects to run as though it has been called like a
normal function.
This patch updates the state mirroring the VFP hardware before entry to
a signal handler so that it adheres to the PCS. Furthermore, we disable
VFP to ensure that we trap on any floating point operation performed by
the signal handler and synchronise the hardware appropriately. A check
is inserted after the signal handler to avoid redundant flushing if VFP
was not used.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The user VFP state must be preserved (subject to ucontext modifications)
across invocation of a signal handler and this is currently handled by
vfp_{preserve,restore}_context in signal.c
Since this code requires intimate low-level knowledge of the VFP state,
this patch moves it into vfpmodule.c.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PL310 errata #588369 and #727915 require writes to the debug registers
of the cache controller to work around known problems. Writing these
registers on L220 may cause deadlock, so ensure that we only perform
this operation when we identify a PL310 at probe time.
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The workaround for PL310 erratum #753970 can lead to deadlock on systems
with an L220 cache controller.
This patch makes the workaround effective only when the cache controller
is identified as a PL310 at probe time.
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Erratum #326103 ("FSR write bit incorrect on a SWP to read-only memory")
only affects the ARM 1136 core prior to r1p0. The workaround
disassembles the faulting instruction to determine whether it was a read
or write access on all v6 cores.
An issue has been reported on the ARM 11MPCore whereby loading the
faulting instruction may happen in parallel with that page being
unmapped, resulting in a deadlock due to the lack of TLB broadcasting
in hardware:
http://lists.infradead.org/pipermail/linux-arm-kernel/2012-March/091561.html
This patch limits the workaround so that it is only used on affected
cores, which are known to be UP only. Other v6 cores can rely on the
FSR to indicate the access type correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure each button is individually identifiable by using
their correct unique given device names.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This creates Device Tree bindings for the Nomadik GPIO driver.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Split off from the patch actually implementing the bindings]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To allow for proper initialisation of the SMSC9115 Ethernet chip
and other devices which may be connected to the 'external bus',
Device Tree must first enable and traverse though it. This patch
enables the 'external bus' which will facilitate further
initialisation of its suborantate DT nodes.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is believed that the gpio compatible match entry is too long
and cumbersome in its current form. This patch takes steps to
decrease its length by using ST-Microelectronics' abbreviation ST.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is believed that the i2c compatible match entry is too long
and cumbersome in its current form. This patch takes steps to
decrease its length by using ST-Microelectronics' abbreviation ST.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Low EMI (Electro-Magnetic Interference) mode means lower slew
rate on the signals. The Nomadik GPIO controller supports
this so create an interface to enable it.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
omapdss driver needs to use the omap_pm_set_min_bus_tput(), so add a new
entry for that in omapdss's platform data, and set it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Pull ARM fixes from Russell King:
"Here's my usual Sunday push, just for one revert which PeterZ hollered
about after last weeks push. Other than that, all seems strangely
quiet as far as fixes go in non-platform ARM land at the moment."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
Revert "ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus"
Pull powerpc fixes from Benjamin Herrenschmidt:
"Here are a few fixes for powerpc. Note the addition to the generic
irq.h. This is part of a 3-patches regression fix for mpic due to
changes in how IRQ_TYPE_NONE is being handled. Thomas agreed to the
addition of the new IRQ_TYPE_DEFAULT contant, however he hasn't
replied with an Ack to the actual patch yet. I don't to wait much
longer with these patches tho."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mpic: Properly set default triggers
irq: Add IRQ_TYPE_DEFAULT for use by PIC drivers
powerpc/mpic: Fix confusion between hw_irq and virq
powerpc/pmac: Don't add_timer() twice
powerpc/eeh: Fix crash caused by null eeh_dev
powerpc/mpc85xx: add MPIC message dts node
powerpc/mpic_msgr: fix offset error when setting mer register
powerpc/mpic_msgr: add lock for MPIC message global variable
powerpc/mpic_msgr: fix compile error when SMP disabled
powerpc: fix build when CONFIG_BOOKE_WDT is enabled
powerpc/85xx: don't call of_platform_bus_probe() twice
This gets rid of the unused default senses array, and replaces the
incorrect use of IRQ_TYPE_NONE with the new IRQ_TYPE_DEFAULT for
the initial set_trigger() call when mapping an interrupt.
This in turn makes us read the HW state and update the irq desc
accordingly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
mpic_is_ipi() takes a virq and immediately converts it to a hw_irq.
However, one of the two call sites calls it with a ... hw_irq. The
other call site also happens to have the hw_irq at hand, so let's
change it to just take that as an argument. Also change mpic_is_tm()
for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If the interrupt and the timeout happen roughly at the same
time, we can get into a situation where the timer function
is run while the interrupt has already been processed. In
this case, the timer function might end up doing an add_timer
on an already pending timer, causing a BUG_ON() to trigger.
Instead, just skip the whole timeout operation if we see that
the timer is pending. The spinlock ensures that the only way
that happens is if we already started a new operation and thus
the timeout can be ignored.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The problem was reported by Anton Blanchard. While EEH error
happened to the PCI device without the corresponding device
driver, kernel crash was seen. Eventually, I successfully
reproduced the problem on Firebird-L machine with utility
"errinjct". Initially, the device driver for Emulex ethernet
MAC has been disabled from .config and force data parity on
the Emulex ethernet MAC with help of "errinjct". Eventually,
I saw the kernel crash after issueing couple of "lspci -v"
command.
The root cause behind is that the PCI device, including the
reference to the corresponding eeh device, will be removed
from the system while EEH does recovery. Afterwards, the
PCI device will be probed again and added into the system
accordingly. So it's not safe to retrieve the eeh device from
the corresponding PCI device after the PCI device has been removed
and not added again.
The patch fixes the issue and retrieve the eeh device from OF node
instead of PCI device after the PCI device has been removed.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Tested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We must use pinctrl framework instead of defining per SoC pinmux drivers. This
patch removes existing padmux support present for SPEAr platform.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
The register and irq definitions in mach/*.h for spear3xx and
spear6xx are now mostly obsolete, after the platforms have been
converted to device tree based probing and the data is now
part of the device tree files.
The misc_regs.h contents are moved into clock.c because that is
the only user, aside from the DMA_CHN_CFG that should eventually
get handled differently. Some of the contents of mach/spear.h
still remain, because they are used to set up the static map table,
timer, uart and auxdata tables, but almost everything got removed.
We might remove everything but the map table as the DT conversion
completes, but that is not a priority. I've also made sure to
make both copies of spear.h more or less identical so we can
eventually combine them.
The spear3?0.h files were only used by the spear3?0.c files, so I
merged the contents in there and removed the bits that were unused.
This is something that should still be looked at.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Recently device tree support is added for SPEAr3xx & SPEAr6xx and we must
upgrade defconfig for that to get compiled. This patches does it.
There are few more rearrangements done in defconfig automatically, when i run
make savedefconfig.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Both SPEAr3xx and SPEAr6xx families have one instance of ARM PL080 DMA
controller. This patch adds in support for that.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
This patch adds a generic target for SPEAr3xx machines that can be configured
via the device-tree. Currently the following devices are supported via the
devicetree:
- VIC interrupts
- PL011 UART
- PL061 GPIO
- PL110 CLCD
- SP805 WDT
- Synopsys DW I2C
- Synopsys DW ethernet
- ST FSMC-NAND
- ST SPEAR-SMI
- ST SPEAR-KEYBOARD
- ST SPEAR-RTC
- ARASAN SDHCI-SPEAR
- SPEAR-EHCI
- SPEAR-OHCI
Other peripheral devices will follow in later patches.
This also removes IO_ADDRESS macro and creates 16 MB static mappings instead of
4K for individual peripherals. This is done to have efficient TLB lookup for any
I/O windows that are located closely together. ioremap() on this range will
return this mapping only instead of creating another.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
For better print logs/messages, it is advisable to use pr_*() routines instead
of directly calling printks. This patch removes direct calling of printks for
spear3xx.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
'make dtbs' compiles all dtbs for a family. For this we need to add entries for
all board dtb's in Makefile.boot file. This patch does it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
This patch adds following clocks: "usbh.0_clk" and "usbh.1_clk". They are used
by ehci and ohci drivers for SPEAr3xx usb host devices.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Change FSMC and SMI clock names to match the ones needed for DT based
probing.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@st.com>
Nicolas Ferre <nicolas.ferre@atmel.com> writes:
First batch of AT91 cleanup for 3.5 kernel.
- The biggest improvement of this series is the ability to compile several
AT91 SoCs in one kernel image.
For now on it's limited to the DT-enabled boards but we can compile all
the core together.
- The Kconfig series is stacked before other patches as it is simple and
non-intrusive. Its goal is to remove too restrictive dependencies on
SoC names. This will allow to add support for newer SoC seamlessly.
- Some very "cosmetic" Kconfig changes are also added (entry names,
comments, etc.).
* tag 'at91-3.5-cleanup' of git://github.com/at91linux/linux-at91: (19 commits)
ARM: at91: add defconfig for device tree
ARM: at91/dt: do not specify the board any more
ARN: at91: introduce SOC_AT91xxx define to allow to compile SoC core support
ARM: at91: add SOC_AT91SAM9 kconfig option to factorise select
ARM: at91: pm select memory controler at runtime
ARM: at91: move at91_init_leds to board init
ARM: at91: do not pin mux the UARTs in init_early
ARM: at91: drop at91_set_serial_console
ARM: at91: uncompress: autodetect the uart to use
ARM: at91: uncompress Store UART address in a variable
hwrng: Kconfig: remove dependency for atmel-rng driver
Input: Kconfig: remove dependency for atmel_tsadcc driver
rtc: Kconfig: remove dependency for AT91 rtc driver
ARM: at91/Kconfig: website link for AT91SAM9G20-EK
ARM: at91/Kconfig: add AT91SAM9x5 family to AT91_EARLY_DBGU0 entry
ARM: at91/Kconfig: add clarifications to AT91SAM9M10G45-EK entry
ARM: at91/Kconfig: add comment to at91sam9x5 family entry
ARM: at91/Kconfig: change at91sam9g45 entry
ARM: at91: change AT91 Kconfig entry comment
Also updates the cleanup branch to v3.4-rc3.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Booting a 3.2, 3.3, or 3.4-rc4 kernel on an Atari using the
`nfeth' ethernet device triggers a WARN_ONCE() in generic irq
handling code on the first irq for that device:
WARNING: at kernel/irq/handle.c:146 handle_irq_event_percpu+0x134/0x142()
irq 3 handler nfeth_interrupt+0x0/0x194 enabled interrupts
Modules linked in:
Call Trace: [<000299b2>] warn_slowpath_common+0x48/0x6a
[<000299c0>] warn_slowpath_common+0x56/0x6a
[<00029a4c>] warn_slowpath_fmt+0x2a/0x32
[<0005b34c>] handle_irq_event_percpu+0x134/0x142
[<0005b34c>] handle_irq_event_percpu+0x134/0x142
[<0000a584>] nfeth_interrupt+0x0/0x194
[<001ba0a8>] schedule_preempt_disabled+0x0/0xc
[<0005b37a>] handle_irq_event+0x20/0x2c
[<0005add4>] generic_handle_irq+0x2c/0x3a
[<00002ab6>] do_IRQ+0x20/0x32
[<0000289e>] auto_irqhandler_fixup+0x4/0x6
[<00003144>] cpu_idle+0x22/0x2e
[<001b8a78>] printk+0x0/0x18
[<0024d112>] start_kernel+0x37a/0x386
[<0003021d>] __do_proc_dointvec+0xb1/0x366
[<0003021d>] __do_proc_dointvec+0xb1/0x366
[<0024c31e>] _sinittext+0x31e/0x9c0
After invoking the irq's handler the kernel sees !irqs_disabled()
and concludes that the handler erroneously enabled interrupts.
However, debugging shows that !irqs_disabled() is true even before
the handler is invoked, which indicates a problem in the platform
code rather than the specific driver.
The warning does not occur in 3.1 or older kernels.
It turns out that the ALLOWINT definition for Atari is incorrect.
The Atari definition of ALLOWINT is ~0x400, the stated purpose of
that is to avoid taking HSYNC interrupts. irqs_disabled() returns
true if the 3-bit ipl & 4 is non-zero. The nfeth interrupt runs at
ipl 3 (it's autovector 3), but 3 & 4 is zero so irqs_disabled() is
false, and the warning above is generated.
When interrupts are explicitly disabled, ipl is set to 7. When they
are enabled, ipl is masked with ALLOWINT. On Atari this will result
in ipl = 3, which blocks interrupts at ipl 3 and below. So how come
nfeth interrupts at ipl 3 are received at all? That's because ipl
is reset to 2 by Atari-specific code in default_idle(), again with
the stated purpose of blocking HSYNC interrupts. This discrepancy
means that ipl 3 can remain blocked for longer than intended.
Both default_idle() and falcon_hblhandler() identify HSYNC with
ipl 2, and the "Atari ST/.../F030 Hardware Register Listing" agrees,
but ALLOWINT is defined as if HSYNC was ipl 3.
[As an experiment I modified default_idle() to reset ipl to 3, and
as expected that resulted in all nfeth interrupts being blocked.]
The fix is simple: define ALLOWINT as ~0x500 instead. This makes
arch_local_irq_enable() consistent with default_idle(), and prevents
the !irqs_disabled() problems for ipl 3 interrupts.
Tested on Atari running in an Aranym VM.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Michael Schmitz <schmitzmic@googlemail.com> (on Falcon/CT60)
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
For now, it just contains the hack for cirrusfb on Amiga, which is moved
out of <video/vga.h> with some slight modifications (use raw_*() instead of
z_*(), which are defined on all m68k platforms).
This makes it safe to include <video/vga.h> in all contexts. Before it
could fail to compile with
include/video/vga.h: In function ‘vga_mm_r’:
include/video/vga.h:242: error: implicit declaration of function ‘z_readb’
include/video/vga.h: In function ‘vga_mm_w’:
include/video/vga.h:247: error: implicit declaration of function ‘z_writeb’
include/video/vga.h: In function ‘vga_mm_w_fast’:
include/video/vga.h:253: error: implicit declaration of function ‘z_writew’
or
include/video/vga.h:23:21: error: asm/vga.h: No such file or directory
depending on the value of CONFIG_AMIGA.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
drivers/usb/musb/musb_io.h provides default implementations for
{read,write}s[bwl]() on most platforms, some of which will conflict soon
with platform-specific counterparts on m68k.
To avoid having to add more platform-specific checks to musb_io.h later,
make sure {read,write}s[bwl]() are always defined on m68k, and disable the
default implementations in musb_io.h on m68k, like is already done for
several other architectures.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Commit d065bd810b
(mm: retry page fault when blocking on disk transfer) and
commit 37b23e0525
(x86,mm: make pagefault killable)
The above commits introduced changes into the x86 pagefault handler
for making the page fault handler retryable as well as killable.
These changes reduce the mmap_sem hold time, which is crucial
during OOM killer invocation.
Port these changes to m68k.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Device interrupts numbers were changed to unsigned int in 1997, the year
IRQ_MACHSPEC was killed as well.
Also kill a related cast while we're at it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: netdev@vger.kernel.org
module_init() maps to device_initcall(), opening the possibility of
race conditions between platform_driver_probe() and registering platform
devices.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This patch updates the defconfig for the LPC32xx SoC after device tree
conversion:
* Adjustment to DT conversion, added new driver support
* Added IPv6
* Increased kernel log buffer
Signed-off-by: Roland Stigge <stigge@antcom.de>
This patch adds the dts files for the reference machine of LPC32xx:
* arch/arm/boot/dts/lpc32xx.dtsi: Include for devices based on LPC32xx
* arch/arm/boot/dts/phy3250.dts: Board support for PHYTEC phyCORE-LPC3250
Signed-off-by: Roland Stigge <stigge@antcom.de>
This patch adjusts the clocks of the LPC32xx SoC to be picked up correctly by
the respective drivers.
* AMBA dmaengine
* watchdog
* I2C
* TSC
* MMC
* Ethernet
* ADC
* USB Device
(All except the pl08xdmac AMBA dmaengine via DT generated device name)
Signed-off-by: Roland Stigge <stigge@antcom.de>
The platforms using i2c-pnx.c both defined a duplicated i2c.h (used nowhere
else). This patch removes those and integrates the contents into the driver
itself.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
