This has been successfully tested on Netgear R6250 and two other
development (unnamed) devices, all of them BCM4708 based.
We also got a possitive feedback from R7000 (BCM4709) tester.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Pull "Samsung fixes for v3.18" from Kukjin Kim:
- explicitly set dr_mode on exynos5250-snow
this is required when kernel is built with USB gadget support.
* tag 'samsung-fixes-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Explicitly set dr_mode on exynos5250-snow
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch removes unused dt node of command line from Exynos3250-based
Rinato board because kernel use the command line from bootloader.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds new board dts file to support Samsung Monk board which
is based on Exynos3250 SoC and has different H/W configuration from
Rinato.
This dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power key
Signed-off-by: Youngjun Cho <yj44.cho@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This adds a node for the IR remote control receiver to the Amlogic
Meson DTS.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are currently 2 differents naming conventions used between the
existing Armada SoC DT files for pinctrl entries (*_pin(s): *-pin(s)
and pmx_*: pmx-*) with a vast majority of files using the former:
$ grep _pin arch/arm/boot/dts/armada-*.dts* | wc -l
155
$ grep pmx arch/arm/boot/dts/armada-*.dts* | wc -l
13
In fact, only some Armada XP files are using the second variant.
This patch normalizes those files (mainly ge0/1 entries) to use
the first variant.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/00114c3169e1d93259ff4150ed46ee36eae16b1e.1416670812.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Felipe writes:
usb: patches for v3.19 merge window
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch adds missed resets property for CSR SiRFatlasVI SPI nodes.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
this patch adds missed resets property for CSR SiRFatlasVI Video Post
Processor(VPP) node.
Signed-off-by: Renwei Wu <renwei.wu@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
this patch adds missed resets property for CSR SiRFprimaII Video Post
Processor(VPP) node.
Signed-off-by: Renwei Wu <renwei.wu@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
this patch adds missed resets property for CSR SiRFprimaII GPS
related nodes.
Signed-off-by: Tao Huang <Tao.Huang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
The I2S controller can use the external clock as reference clock with
master mode. But based on different hardware or software design, this
external clock might be needed or not needed.
So the external input pin can be an independent pinctrl group, and the
card driver can decice to get it or not.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The I2S controller can output mclk to external audio codec. But by
hardware design, some codecs need mclk and some codecs do not need
mclk. So the mclk pin can be an independent pinctrl group, and the
card driver can get it or not based on boards.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Allwinner Clocks additions for 3.19
A few patches that should go through the clock tree, mostly fixes, cleanups,
and new clocks additions to start to support the A80.
When a thermal temperature is invoked use the CRU to reset the chip
on rk3288-evb boards. TSHUT is low active on these boards.
Signed-off-by: Caesar Wang <caesar.wang@rock-chips.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
If for some reason we are unable to shut it down in orderly fashion
(kernel is stuck holding a lock or similar), then hardware TSHUT will
reset it.
If the temperature is over 95C over a period of time the thermal shutdown
of the tsadc is invoked with can either reset the entire chip via the CRU,
or notify the PMIC via a GPIO. This should be set in the specific board.
Signed-off-by: Caesar Wang <caesar.wang@rock-chips.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch changes a dtsi file to contain the thermal data
on RK3288 and later SoCs. This data will
enable a thermal shutdown over 90C.
Signed-off-by: Caesar Wang <caesar.wang@rock-chips.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
DCAN1 is routed to CAN port (J11) when Profile 1 is selected on the
profile selection switch.
Provide information for DCAN1 pins and node but keep it disabled
by default. User has to manually enable it if Profile 1 is chosen.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "raminit-syscon" property to specify the RAMINIT register.
Add clock information.
Rename can nodes from "d_can" to "can" to be compliant
with the ePAPR specs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use syscon regmap to expose the Control module register space.
This register space is shared between many users e.g. DCAN, USB, display, etc.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DCAN support for AM437x GP EVM with both DCAN instances.
[Roger Q] Updated output pin to not use pull up.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use syscon regmap to expose the Control module register space.
This register space is shared between many users e.g. DCAN, USB, display, etc.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board has 2 CAN ports but only the first one can be used.
Enable the first CAN port.
WAKEUP0 pin doesn't have INPUT enable bit so we just disable
weak PULLs.
The second CAN port cannot be used without hardware modification
so we don't enable the second port.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board has 2 CAN ports but only the first one can be used.
Enable the first CAN port.
WAKEUP0 pin doesn't have INPUT enable bit so we just disable
weak PULLs.
The second CAN port cannot be used without hardware modification
so we don't enable the second port.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Display and DCAN drivers use syscon regmap to access some registers
in the CORE control area. Add the syscon regmap node for this
area.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Review of the u-boot sunxi simplefb patches has led to the decision that
u-boot should not use a specific path to find the nodes as this goes contrary
to how devicetree usually works.
Instead a platform specific compatible + properties should be used for this.
The simplefb bindings have already been updated to reflect this, this patch
brings the sunxi devicetree files in line with the new binding, and the
actual u-boot implementation as it is going upstream.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Avoid the parent pll for the mod-clk for de_be0 getting disabled when non of
the other users are enabled (which can happen when none of i2c, spi and mmc
are in use).
Note for now we point directly to the parent rather then to the de_be0 mod-clk
as that is not modelled in our devicetree yet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The apb2 clocks are actually the same as apb1 clocks on the other sunxi
platforms, hence compatible with "allwinner,sun4i-a10-apb1-clk".
Update the dtsi to use the new unified apb1 clk.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With the new factors infrastructure in place, we can unify apb1 and
apb1_mux as a single clock now.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
[wens@csie.org: Change apb1 node label to "apb1"; reword commit title]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
