Store the length of the skb before transmitting it and use it for stats
instead of skb->len, since skb might have been freed already.
This issue was discovered using the Kernel Address sanitizer (KASan).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not use the length of the transmitted skb (which was freed), but
that of the response skb.
This issue was discovered using the Kernel Address sanitizer (KASan).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we only checked if the transmission queue is not full in the
middle of the xmit function. This lead to complex logic due to the fact
that sometimes we need to reallocate the headroom for our Tx header.
Allow the switch driver to know if the transmission queue is not full
before sending the packet and remove this complex logic.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This resolves compile errors on um-allyesconfig.
Note that there are many other drivers which have the same issue.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
System ports are unique identifiers in a multi-ASIC environment that
represent all the available ports in the system. Local ports on the
other hand, are unique only within the local ASIC.
Since system port to local port mapping is not part of the HW-SW
contract and since only single-ASIC configurations are currently
supported, set an explicit 1:1 mapping by configuring the Switch System
Port Record (SSPR) register.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a port's netdevice we should also free the memory
allocated by alloc_etherdev(). Do this by calling free_netdev() at the
end of the teardown sequence.
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address in the switchdev_obj_fdb structure is currently represented
as a pointer. Replacing it for a 6-byte array allows switchdev to carry
addresses directly read from hardware registers, not stored by the
switch chip driver (as in Rocker).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-08-05
This series contains updates to i40e, i40evf and e1000e.
Anjali adds support for x772 devices to i40e and i40evf. With the added
support, x772 supports offloading of the outer UDP transmit and receive
checksum for tunneled packets. Also supports evicting ATR filters in the
hardware, so update the driver with this new feature set.
Raanan provides several fixes for e1000e, first rectifies the Energy
Efficient Ethernet in Sx code so that it only applies to parts that
actually support EEE in Sx. Fix whitespace and moved ICH8 related define
to the proper context. Fixed the ASPM locking which was reported by
Bjorn Helgaas. Fix a workaround implementation for systime which could
experience a large non-linear increment of the systime value when
checking for overflow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Added physical port counters in the following standard formats to
ethtool statistics:
- IEEE 802.3
- RFC2863
- RFC2819
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that TIRs, TISs and flow tables are kept alive while the netdev is
stopped (after executing ndo_stop()) we can do the following
improvements:
- Obsolete the active_vlans SW shadow.
- Do not delete/add flow table rules upon ndo_stop/open.
In addition to simplifying the flow, this change also fastens
the ndo_open/close operations.
- Obsolete synchronization of threads accessing the flow tables
with the netdev stop/open threads.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It does not make sense to allow events while the netdev is
unregistered.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename some functions that used to be invoked upon ndo_open/stop and
are now invoked upon create/destroy_netdev() in order to better hint
their place in the flow.
Change some functions location in the file so that functions involved
in ndo_open/stop flow will not be interleaved with other functions.
This is a cosmetic change, no logical change here.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create/destroy TIRs, TISs and flow tables upon PCI probe/remove rather
than upon the netdev ndo_open/stop.
Upon ndo_stop(), redirect all RX traffic to the (lately introduced)
"Drop RQ" and then close only the RX/TX rings, leaving the TIRs,
TISs and flow tables alive.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be used by the mlx5 Eth driver in following commit.
This is in preparation for netdev "light-weight" open/stop flow
change described in previous commit.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX traffic routed to this RQ will be silently dropped, at the NIC HW
level.
This is in preparation for netdev "light-weight" open/stop flow
change described in previous commit.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generally an RX packet flows through the following objects:
Flow table --> TIR --> RQT --> RQ
Where:
- TIR stands for "Transport Interface Receive", defining the RSS and
LRO paramaters.
- RQT stands for "RQ Table", implementing the RSS indirection table.
- RQ stands for "Receive Queue"
For flows that do not need LRO, nor RSS, the driver made a shortcut to
the above RX flow by pointing to the RQ directly from the TIR, yielding
this flow:
Flow table --> TIR --> RQ
In this commit we remove this shortcut by "inserting" a single-RQ RQT
between the TIR and the RQ, i.e RX packets will reach the same RQ but
will go through an RQT of size 1, pointing to just a single RQ.
This way the RX traffic re-direction to/from the "Drop RQ" will be more
uniform (AKA "one flow"), as it will involve only RQTs re-direction and
no TIRs re-direction.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of processing tx events in isr adding separate napi for
tx which improves performance by ~180Mbps with
omap2plus_defconfig on DRA74x platform. Also cleaning up rx napis
by renaming to napi_rx for better understanding the code.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since interrupt is shared between the two ethernet interface and
in isr only one napi is scheduled at an instance so having two
napis doesn't make any difference. So making napi also as a
common resource for the dual ethernet interfaces.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW interrupts can be disabled by masking CPSW interrupts and
clearing interrupt by writing appropriate EOI. So removing all
disable_irq/enable_irq as discussed in [1]
[1] http://patchwork.ozlabs.org/patch/492741/
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 230d00eb4b ("bnx2x: new Multi-function mode - BD") adds support
for the new mode in bnx2x. This expands this support by implementing
APIs required by our storage drivers to support that mode.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After successful register_netdev, we can use netdev_err rather the more
generic dev_err.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set port to NULL if port probe fails so we don't try to remove partially
initialized port on port probe err cleanup path.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the algorithm. Read systimel twice and check for overflow.
If there was no overflow, use the first value.
If there was an overflow, read systimeh again and use the second
systimel value.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements the EEE in Sx code so that it only applies to parts
that support EEE in Sx (as opposed to all parts that support EEE).
It also uses the existing eee_advert and eee_lp_abiliity to set just the
bits (100/1000) that should be set.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports IWARP, this patch handles checking for PE critical errors.
Since the driver doesn't support the IWARP interface for now, this patch
just does bare minimum to log a message oif a PE critical error
happens.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 fixes an issue from X710 where TX descriptor WB would not happen if
the interrupts were disabled. In order for the write backs to happen a
bit needs to be set in the dynamic interrupt control register called
WB_ON_ITR. With this feature, the SW driver need not arm SW interrupts to
work around the issue in X710.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 uses the admin queue to configure RSS. This patch adds the necessary
flow changes to configure RSS through AQ. It also adds the separate VMDQ2
lookup tables and hash key programming for X722.
X722 also exposes a different set of PCTYPES for RSS, this patch
accommodates those changes.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Read the correct bits of PL Who Am I for the Source PF field which has
changed in T6
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to dump edc bist status for ECC data errors
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debug support to dump memory address ranges of various hardware
modules of the adapter.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rocker supports the transmission of scattered packets, so let the kernel
know about it by setting the NETIF_F_SG bit in the device's features.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05cc5a39dd ("bnx2x: add vlan filtering offload") has introduced
an incorrect logic for checking whether pvid should be configured for
a vf, causing the hypervisor driver to send unneeded ramrods for all of
the vfs each time a pvid has changed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a poll controller for netconsole which invokes the RX
interrupt handler to poll for incoming packets, and cleans up all TX
queues by invoking the TX interrupt handler.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a poll controller for netconsole which invokes both of our
interrupt handlers for the different RX/TX queues.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
