Add support for external control over GPIO for LDO10, LDO11 and LDO12
S2MPS14 regulators. External control can be turned on by writing 0x0 to
control register which in case of other regulators is used for disabling
them. These LDO10-LDO12 regulators can be disabled only by I2C GPIO or
PWREN pin so the patch actually allows proper way of disabling them.
Additionally the GPIO control has two benefits:
- It is faster than toggling it over I2C bus.
- It allows disabling the regulator during suspend to RAM; The AP will
enable it during resume.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Refactor code for parsing DTS to increase a little code readability. The
behaviour should not change.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Don't store pointer to regulator_dev returned by
devm_regulator_register() in state container. It isn't used anywhere
outside of probe.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently the regulator core does not take an additional reference to
the of_node it is passed. This means that the caller must ensure that
the of_node is valid for the duration of the regulator's existance.
It is reasonable for the framework to assume it is passed a valid
of_node but seems onerous for it to assume the caller will keep the node
valid for the life-time of the regulator, especially when
devm_regulator_register is used and there will likely be no code in the
driver called at the point it would be safe to put the of_node.
This patch adds an additional of_node_get when the regulator is
registered and an of_node_put when it is unregistered in the core. This
means individual drivers are free to put their of_node references at the
end of probe letting the regulator core handling it from there. This
simplifies code on the driver side.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As of_regulator_match will take an of_node reference to each matched
regulator, it makes sense to provide a helper to put all those
references. This patch does that.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently, of_regulator_match does not increment the reference count of
the of_nodes it takes new references to. This could cause the node
pointer held to be invalid, by the time it is passed to the regulator
core. This patchs adds an of_node_get when we copy each of_node pointer
into the match structure.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
AXP202 and AXP209 come with two synchronous step-down DC-DCs and five
LDOs. This patch introduces basic support for those regulators.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull regulator fixes from Mark Brown:
"A few driver specific fixes that have come in over the merge window,
all only relevant for the specific driver"
* tag 'regulator-v3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: bcm590xx: Set n_voltages for linear reg
regulator: s5m8767: Fix carried over ena_gpio assignment
regulator: s2mps11: Don't check enable_shift before setting enable ramp rate
regulator: s2mpa01: Don't check enable_shift before setting enable ramp rate
Pull MMC updates from Chris Ball:
"MMC highlights for 3.15:
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
- Add GPIO descriptor based slot-gpio card detect API
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
- mmci: Support HW busy detection on ux500
- omap: Support MMC_ERASE
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
- rtsx: Support pre-req/post-req async
- sdhci: Add support for Realtek RTS5250 controllers
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"
* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
mmc: sdhci-acpi: Intel SDIO has broken card detect
mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
mmc: sdhci-msm: Add platform_execute_tuning implementation
mmc: sdhci-msm: Initial support for Qualcomm chipsets
mmc: sdhci-msm: Qualcomm SDHCI binding documentation
sdhci: only reprogram retuning timer when flag is set
mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
mmc: sdhci: Allow for irq being shared
mmc: sdhci-acpi: Add device id 80860F16
mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
mmc: slot-gpio: Split out CD IRQ request into a separate function
mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
mmc: sdhci-spear: use generic card detection gpio support
mmc: sdhci-spear: remove support for power gpio
mmc: sdhci-spear: simplify resource handling
mmc: sdhci-spear: fix platform_data usage
mmc: sdhci-spear: fix error handling paths for DT
mmc: sdhci-bcm-kona: fix build errors when built-in
...
During registration of regulators if external control for regulator was
set in DTS the ena_gpio and ena_gpio_flags fields of regulator_config
were set to proper values.
However the same regulator_config was used in next iterations of loop so
the ena_gpio fields carried over to next regulators.
The issue was not observed as ena_gpio is supported only for Buck9
regulator which is often the last regulator parsed from DTS.
Be sure to clear ena_gpio config fields before registering the
regulator.
Fixes: ee1e0994ab (regulator: s5m8767: Use GPIO for controlling Buck9/eMMC)
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code misses updating the register when enable_shift is 0.
e.g. S2MPS11_BUCK9_RAMP_SHIFT and S2MPS11_BUCK6_RAMP_EN_SHIFT are 0.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code misses updating the register when enable_shift is 0.
e.g. S2MPA01_BUCK4_RAMP_EN_SHIFT is 0.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The voltages in aat2870_ldo_voltages table are in ascendant order, so use
regulator_map_voltage_ascend.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Also remove test for selector in st_pwm_regulator_set_voltage_sel, the checking
is already done in .list_voltage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
On some STMicroelectronics hardware reside regulators consisting
partly of a PWM input connected to the feedback loop. As the PWM
duty-cycle is varied the output voltage adapts. This driver
allows us to vary the output voltage by adapting the PWM input
duty-cycle.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit ca5d1b3524
"regulator: helpers: Modify helpers enabling multi-bit control",
we can set enable_val setting for device that use multiple bits for control.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This regulator is used for system IO and is fixed to 1.8V. Let's give
consumers the option to fetch the voltage level.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
S2MPS14 regulators support suspend mode where their status is controlled
by PWREN coming from SoC. This patch implements the set_suspend_disable
for S2MPS14 regulators.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for S2MPS14 PMIC regulators to s2mps11 driver. The S2MPS14
has fewer BUCK-s and LDO-s than S2MPS11. It also does not support
controlling the BUCK ramp delay.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For a constant format without additional arguments, use seq_puts()
instead of seq_printf(). Also, it fixes the following checkpatch
warning.
WARNING: Prefer seq_puts to seq_printf
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Silences the following warning type:
WARNING: Missing a blank line after declarations
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove checking control_reg in [set|get]_voltage_sel and then convert to use
regulator_[set|get]_voltage_sel_regmap for [set|get]_voltage_sel callbacks.
The anatop-reg-offset property is a required property rather than optional
property. So the question is what is the meaning of setting anatop-reg-offset
to 0? If 0 is a valid setting for anatop-reg-offset and it has special meaning,
we had better document it in the binding document. Otherwise, remove the testing
for control_reg in the driver.
No anatop voltage regulator node in the dts files set anatop-reg-offset to 0.
So I think it's safe to remove testing if control_reg is 0.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Silences the following type of checkpatch warning:
WARNING: Missing a blank line after declarations
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Silences the following type of checkpatch warning:
WARNING: Missing a blank line after declarations
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Silences the following type of error/warnings:
ERROR: that open brace { should be on the previous line
WARNING: Missing a blank line after declarations
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Both 5102 and 8997 have the regulator capable of supplying 1.8V, and the
voltage step from the 5110 regulator is different from what is specified
in the default description. This patch updates the default regulator
description to match 5110 and selects the 1.8V capable description for
8997.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Now we are using devm_regulator_register(), so we don't need the rdev[] array
to store return value of devm_regulator_register. Use a *rdev variable is
enough for checking return status.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
cppcheck detected an incorrect assignment:
drivers/regulator/da9063-regulator.c:711]: (warning) Assignment
of function parameter has no effect outside the function
the original code didn't do anything, instead, *da9063_reg_matches
needs to be set to NULL.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a regulator driver for the BCM590xx PMU voltage regulators.
The driver supports LDOs and DCDCs in normal mode only. There is
no support for low-power mode or power sequencing.
Signed-off-by: Matt Porter <mporter@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now we are using devm_regulator_register(), so we don't need the *rdev[] array
to store return value of devm_regulator_register. Use a *rdev variable is
enough for checking return status.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Wenyou Yang <Wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Do not allocate memory for 'struct regulator_dev *' since it was removed
from state container (values returned by devm_regulator_register() are
not used outside of probe).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now we are using devm_regulator_register(), so we don't need to allocate *rdev[]
array to store return value of devm_regulator_register. Use a *rdev variable is
enough for checking return status.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
