Some engines are not available for all Gens. eg, Gen11 introduced
VCS3/VCS4/VECS2, and VCS2 is not supported on some Gen9 machines. So need to
add check before access them.
Signed-off-by: Xinyun Liu <xinyun.liu@intel.com>
Signed-off-by: Yakui Zhao <Yakui.Zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
GVT-g only simulates DP port for guest and leaves EDP_PSR_IMR
and EDP_PSR_IIR registers as default MMIO read/write.
So guest won't get expected initial values of these registers when
initializing the gpu driver, which results in following warning and logs.
--------
Interrupt register 0x64838 is not zero: 0xffffffff
WARNING: CPU: 1 PID: 157 at drivers/gpu/drm/i915/i915_irq.c:177
gen3_assert_iir_is_zero+0x38/0xa0
Call Trace:
gen8_de_irq_postinstall+0xa7/0x400
gen8_irq_postinstall+0x27/0x80
drm_irq_install+0xbc/0x140
i915_driver_load+0xa9d/0xd50
--------
Because GVT-g does not handle EDP(embedded DP) simulation for guests,
always set EDP_PSR_IMR and EDP_PSR_IIR to value 0.
Signed-off-by: Longhe Zheng <longhe.zheng@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
CSFE_CHICKEN1(0x20d4) needs access with mask. This is caught in AcrnGT
conformance check test:
[drm:intel_gvt_vgpu_conformance_check]
*ERROR* gvt: vgpu1 unconformance mmio 0x20d4:0x40004,0x4
Signed-off-by: Xinyun Liu <xinyun.liu@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Previously we assumed two 4-byte writes to the same PTE coming in sequence.
But recently we observed inconsecutive partial write happening as well. So
this patch enhances the previous solution. It now uses a list to save more
partial writes. If one partial write can be combined with another one in
the list to construct a full PTE, update its shadow entry. Otherwise, save
the partial write in the list.
v2: invalidate old entry and flush ggtt (Zhenyu)
v3: split old ggtt page unmap to another patch (Zhenyu)
v4: refine codes (Zhenyu)
Signed-off-by: Hang Yuan <hang.yuan@linux.intel.com>
Cc: Yan Zhao <yan.y.zhao@intel.com>
Cc: Xiaolin Zhang <xiaolin.zhang@intel.com>
Cc: Zhenyu Wang <zhenyu.z.wang@intel.com>
Reviewed-by: Xiaolin Zhang <xiaolin.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Previously only cancelled dma map of a ggtt page when the ggtt entry was
cleared. This patch will cancel dma map of an old ggtt page as well when
the ggtt entry is updated with new page address.
Fixes: 7598e8700e9a(drm/i915/gvt: Missed to cancel dma map for ggtt entries)
Signed-off-by: Hang Yuan <hang.yuan@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
When one vgpu is destroyed, its ggtt entries are not cleared.
This patch clears ggtt entries to avoid information leak.
v2: add 'Fixes' tag (Zhenyu)
Fixes: 2707e44466 ("drm/i915/gvt: vGPU graphics memory virtualization")
Signed-off-by: Zhipeng Gong <zhipeng.gong@intel.com>
Reviewed-by: Hang Yuan <hang.yuan@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Host prints lots of untracked MMIO at 0x4653c when creating linux guest.
"gvt: vgpu 2: untracked MMIO 0004653c len 4"
GEN9_CLKGATE_DIS_4 (0x4653c) is accessed by i915 for gmbus clockgating.
However vgpu doesn't support any clockgating powergating operations
on related mmio access trap so need add it to default handler.
GEN9_CLKGATE_DIS_4 is accessed in bxt_gmbus_clock_gating() which only
applies to GEN9_LP so doens't show the warning on other platforms.
The solution is to add it to default handler init_bxt_mmio_info().
Reviewed-by: He, Min <min.he@intel.com>
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Recent patch fixed the call trace
"ERROR Port B enabled but PHY powered down? (PHY_CTL 00000000)".
but introduced another similar call trace shown as:
"ERROR Port C enabled but PHY powered down? (PHY_CTL 00000200)".
The call trace will appear when host and guest enabled different ports,
i.e. host using PORT C or neither PORT is enabled, while guest is always
using PORT B as simulated by gvt. The issue is actually covered previously
before the commit and reverals now when the commit do the right thing.
On BXT, some PHY registers are initialized by vbios, before i915 loaded.
Later i915 will re-program some, or skip some based on the implementation.
The initialized mmio for guest i915 is done by gvt, based on the snapshot
taken from host. If host and guest have different PORT enabled, some
DPIO PHY mmios that gvt initialized for guest i915 will not match the
simualted monitor for guest, which leads to guest i915 print the calltrace
when it's trying to enable PHY and PORT.
The solution is to init these DPIO PHY registers to default value, then
guest i915 will program them to reasonable value based on the default
powerwell table and enabled PORT. Together with the old patch, all similar
call trace in guest kernel on BXT can be resolved.
v2: Move PHY register init to intel_vgpu_reset_mmio (Min)
v3: Do not delete empty line in issue fix patch. (zhenyu)
Fixes: c8ab5ac30c ("drm/i915/gvt: Make correct handling to vreg
BXT_PHY_CTL_FAMILY")
Reviewed-by: He, Min <min.he@intel.com>
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
GVT-g emualte the opregion for guest with bdb version as '186' which
child_device_config length should be '33'.
v2: split into 2 patch. 1st for issue fix, 2nd for code clean up.(Zhenyu)
v3: add fixes tag.(Zhenyu)
Fixes: 4023f301d2 ("drm/i915/gvt: opregion virtualization for win")
CC: Xiaolin Zhang <xiaolin.zhang@intel.com>
Reviewed-by: Xiaolin Zhang <xiaolin.zhang@intel.com>
Signed-off-by: Weinan Li <weinan.z.li@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Handle guest mm access life cycle properly with mmget()/mmput().
As noted by Linus, use_mm() depends on valid live page table but
KVM's mmgrab() doesn't guarantee that. As vGPU usage depends on
guest VM life cycle, need to make sure to use mmget()/mmput() to
guarantee VM address access.
v3: fix build
v2: v1 caused a weird dependence issue which failed for vfio
device release, which result invalid mdev vgpu and kvm state
without proper release taken. This trys to put right reference
around VM address space access instead.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
This trys to give new born vGPU with higher scheduling chance
not only with adding to sched list head and also have higher
priority for workload sched for 2 seconds after starting to
schedule it. In order for fast GPU execution during VM boot,
and ensure guest driver setup with required state given in time.
This fixes recent failure seen on one VM with multiple linux VMs
running on kernel with commit 2621cefaa42b3("drm/i915: Provide a timeout to i915_gem_wait_for_idle() on setup"),
which had shorter setup timeout that caused context state init failed.
v2: change to 2s for higher scheduling period
Cc: Yuan Hang <hang.yuan@intel.com>
Reviewed-by: Hang Yuan <hang.yuan@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Physical plane's tiling mode value is given directly as
drm_format_mod for plane query, which is not correct fourcc
code. Fix it by using correct intel tiling fourcc mod definition.
Current qemu seems also doesn't correctly utilize drm_format_mod
for plane object setting. Anyway this is required to fix the usage.
v3: use DRM_FORMAT_MOD_LINEAR, fix comment
v2: Fix missed old 'tiled' use for stride calculation
Fixes: e546e281d3 ("drm/i915/gvt: Dmabuf support for GVT-g")
Cc: Tina Zhang <tina.zhang@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Colin Xu <Colin.Xu@intel.com>
Reviewed-by: Colin Xu <Colin.Xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
pm_runtime_get_sync in intel_runtime_pm_get might sleep if i915
device is not active. When stop vgpu schedule, the device may be
inactive. So need to move runtime_pm_get out of spin_lock/unlock.
Fixes: b24881e0b0b6("drm/i915/gvt: Add runtime_pm_get/put into gvt_switch_mmio
Cc: <stable@vger.kernel.org>
Signed-off-by: Hang Yuan <hang.yuan@linux.intel.com>
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Recent patch introduce strict check on scanning cmd:
Commit 8d458ea0ec ("drm/i915/gvt: return error on cmd access")
Before 8d458ea0ec, if cmd_reg_handler() checks that a cmd access a mmio
that not marked as F_CMD_ACCESS, it simply returns 0 and log an error.
Now it will return -EBADRQC which will cause the workload fail to submit.
On BXT, i915 applies WaClearHIZ_WM_CHICKEN3 which will program
GEN9_WM_CHICKEN3 by LRI when init wa ctx. If it has no F_CMD_ACCESS flag,
vgpu will fail to start. Also add F_MODE_MASK since it's mode mask reg.
v2: Refresh commit message to elaborate issue symptom in detail.
v3: Make SKL_PLUS share same handling since GEN9_WM_CHICKEN3 should be
F_CMD_ACCESS from HW aspect. (yan, zhenyu)
Signed-off-by: Colin Xu <colin.xu@intel.com>
Acked-by: Zhao Yan <yan.y.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Guest kernel will write to BXT_PHY_CTL_FAMILY to reset DDI PHY
and pull BXT_PHY_CTL to check PHY status. Previous handling will
set/reset BXT_PHY_CTL of all PHYs at same time on receiving vreg
write to some BXT_PHY_CTL_FAMILY. If some BXT_PHY_CTL is already
enabled, following reset to another BXT_PHY_CTL_FAMILY will clear
the enabled BXT_PHY_CTL, which result in guest kernel print:
-----------------------------------
[drm:intel_ddi_get_hw_state [i915]]
*ERROR* Port B enabled but PHY powered down? (PHY_CTL 00000000)
-----------------------------------
The correct handling should operate BXT_PHY_CTL_FAMILY and
BXT_PHY_CTL on the same DDI.
v2: Use correct reg define. The naming looks confusing, however
current i915_reg.h bind DPIO_PHY0 to _PHY_CTL_FAMILY_DDI and
bind DPIO_PHY1 to _PHY_CTL_FAMILY_EDP, pairing to
_BXT_PHY_CTL_DDI_A and _BXT_PHY_CTL_DDI_B respectively.
v3: v2 incorrectly map _PHY_CTL_FAMILY_EDP to _BXT_PHY_CTL_DDI_A.
BXT_PHY_CTL() looks up DDI using PORTx but not PHYx. Based on
DPIO_PHY to DDI mapping, make correct vreg handle to BXT_PHY_CTL
on receiving vreg write to BXT_PHY_CTL_FAMILY. (He, Min)
Current mapping according to bxt_power_wells:
dpio-common-a:
>>> DPIO_PHY1
>>> BXT_DPIO_CMN_A_POWER_DOMAINS
>>> POWER_DOMAIN_PORT_DDI_A_LANES
>>> PORT_A
dpio-common-bc:
>>> DPIO_PHY0
>>> BXT_DPIO_CMN_BC_POWER_DOMAINS
>>> POWER_DOMAIN_PORT_DDI_B_LANES | POWER_DOMAIN_PORT_DDI_C_LANES
>>> PORT_B or PORT_C
Signed-off-by: Colin Xu <colin.xu@intel.com>
Reviewed-by: He, Min <min.he@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Pull IDA updates from Matthew Wilcox:
"A better IDA API:
id = ida_alloc(ida, GFP_xxx);
ida_free(ida, id);
rather than the cumbersome ida_simple_get(), ida_simple_remove().
The new IDA API is similar to ida_simple_get() but better named. The
internal restructuring of the IDA code removes the bitmap
preallocation nonsense.
I hope the net -200 lines of code is convincing"
* 'ida-4.19' of git://git.infradead.org/users/willy/linux-dax: (29 commits)
ida: Change ida_get_new_above to return the id
ida: Remove old API
test_ida: check_ida_destroy and check_ida_alloc
test_ida: Convert check_ida_conv to new API
test_ida: Move ida_check_max
test_ida: Move ida_check_leaf
idr-test: Convert ida_check_nomem to new API
ida: Start new test_ida module
target/iscsi: Allocate session IDs from an IDA
iscsi target: fix session creation failure handling
drm/vmwgfx: Convert to new IDA API
dmaengine: Convert to new IDA API
ppc: Convert vas ID allocation to new IDA API
media: Convert entity ID allocation to new IDA API
ppc: Convert mmu context allocation to new IDA API
Convert net_namespace to new IDA API
cb710: Convert to new IDA API
rsxx: Convert to new IDA API
osd: Convert to new IDA API
sd: Convert to new IDA API
...
Pull drm fixes from Dave Airlie:
"Just a couple of fixes"
One MAINTAINERS address change, two panels fixes, and set of amdgpu
fixes (build fixes, display fixes and some others)"
* tag 'drm-next-2018-08-24' of git://anongit.freedesktop.org/drm/drm:
drm/edid: Add 6 bpc quirk for SDC panel in Lenovo B50-80
drm/amd/display: Don't build DCN1 when kcov is enabled
Revert "drm/amdgpu/display: Replace CONFIG_DRM_AMD_DC_DCN1_0 with CONFIG_X86"
drm/amdgpu/display: disable eDP fast boot optimization on DCE8
drm/amdgpu: fix amdgpu_amdkfd_remove_eviction_fence v3
drm/amdgpu: fix incorrect use of drm_file->pid
drm/amdgpu: fix incorrect use of fcheck
drm/powerplay: enable dpm under pass-through
drm/amdgpu: access register without KIQ
drm/amdgpu: set correct base for THM/NBIF/MP1 IP
drm/amd/display: fix dentist did ranges
drm/amd/display: make dp_ss_off optional
drm/amd/display: fix dp_ss_control vbios flag parsing
drm/amd/display: Do not retain link settings
MAINTAINERS: drm-misc: Change seanpaul's email address
drm/panel: simple: tv123wam: Add unprepare delay
Commit cafa0010cd ("Raise the minimum required gcc version to 4.6")
recently exposed a brittle part of the build for supporting non-gcc
compilers.
Both Clang and ICC define __GNUC__, __GNUC_MINOR__, and
__GNUC_PATCHLEVEL__ for quick compatibility with code bases that haven't
added compiler specific checks for __clang__ or __INTEL_COMPILER.
This is brittle, as they happened to get compatibility by posing as a
certain version of GCC. This broke when upgrading the minimal version
of GCC required to build the kernel, to a version above what ICC and
Clang claim to be.
Rather than always including compiler-gcc.h then undefining or
redefining macros in compiler-intel.h or compiler-clang.h, let's
separate out the compiler specific macro definitions into mutually
exclusive headers, do more proper compiler detection, and keep shared
definitions in compiler_types.h.
Fixes: cafa0010cd ("Raise the minimum required gcc version to 4.6")
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Eli Friedman <efriedma@codeaurora.org>
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are several blockable mmu notifiers which might sleep in
mmu_notifier_invalidate_range_start and that is a problem for the
oom_reaper because it needs to guarantee a forward progress so it cannot
depend on any sleepable locks.
Currently we simply back off and mark an oom victim with blockable mmu
notifiers as done after a short sleep. That can result in selecting a new
oom victim prematurely because the previous one still hasn't torn its
memory down yet.
We can do much better though. Even if mmu notifiers use sleepable locks
there is no reason to automatically assume those locks are held. Moreover
majority of notifiers only care about a portion of the address space and
there is absolutely zero reason to fail when we are unmapping an unrelated
range. Many notifiers do really block and wait for HW which is harder to
handle and we have to bail out though.
This patch handles the low hanging fruit.
__mmu_notifier_invalidate_range_start gets a blockable flag and callbacks
are not allowed to sleep if the flag is set to false. This is achieved by
using trylock instead of the sleepable lock for most callbacks and
continue as long as we do not block down the call chain.
I think we can improve that even further because there is a common pattern
to do a range lookup first and then do something about that. The first
part can be done without a sleeping lock in most cases AFAICS.
The oom_reaper end then simply retries if there is at least one notifier
which couldn't make any progress in !blockable mode. A retry loop is
already implemented to wait for the mmap_sem and this is basically the
same thing.
The simplest way for driver developers to test this code path is to wrap
userspace code which uses these notifiers into a memcg and set the hard
limit to hit the oom. This can be done e.g. after the test faults in all
the mmu notifier managed memory and set the hard limit to something really
small. Then we are looking for a proper process tear down.
[akpm@linux-foundation.org: coding style fixes]
[akpm@linux-foundation.org: minor code simplification]
Link: http://lkml.kernel.org/r/20180716115058.5559-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Christian König <christian.koenig@amd.com> # AMD notifiers
Acked-by: Leon Romanovsky <leonro@mellanox.com> # mlx and umem_odp
Reported-by: David Rientjes <rientjes@google.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Sudeep Dutt <sudeep.dutt@intel.com>
Cc: Ashutosh Dixit <ashutosh.dixit@intel.com>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reorder allocation to avoid an awkward lock/unlock/lock sequence.
Simpler code due to being able to use ida_alloc_max(), even if we can't
eliminate the driver's spinlock.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
DCN1 contains code that utilizes fp math. When
CONFIG_KCOV_INSTRUMENT_ALL and CONFIG_KCOV_ENABLE_COMPARISONS are
enabled, build errors are found. See this earlier patch for details:
https://lists.freedesktop.org/archives/dri-devel/2018-August/186131.html
As a short term solution, disable CONFIG_DRM_AMD_DC_DCN1_0 when
KCOV_INSTRUMENT_ALL and KCOV_ENABLE_COMPARISONS are enabled. In
addition, make it a fully derived config, taking into account
CONFIG_X86.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix quite a number of bugs here. Unfortunately only compile tested.
v2: fix copy&paste error
v3: fix 80 chars issue in comment
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Repeat enable dpm under pass-through because there is no actually
hardware-fini and real power-off when guest vm shutdown or reboot.
Otherwise, under pass-through it will be failed to populate populate
and upload SCLK MCLK DPM levels due to zero of pcie_speed_table.count.
Signed-off-by: Yintian Tao <yttao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
there is no need to access register such as mmSMC_IND_INDEX_11
and mmSMC_IND_DATA_11 through KIQ because they are VF-copy.
Signed-off-by: Yintian Tao <yttao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Do not retrain link settings if lane count and link rate are both
unknown. Causes driver to be stuck reading VBIOS register after
removing emulated connection.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull MFD updates from Lee Jones:
"New Drivers:
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
New Device Support:
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
New Functionality:
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
Fix-upsL
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
Bug Fixes:
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501"
* tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (60 commits)
mfd: madera: Add register definitions for accessory detect
mfd: sm501: Set coherent_dma_mask when creating subdevices
mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
mfd: bd71837: Core driver for ROHM BD71837 PMIC
media: platform: cros-ec-cec: Fix dependency on MFD_CROS_EC
mfd: sec-core: Export OF module alias table
mfd: as3722: Disable auto-power-on when AC OK
mfd: axp20x: Support AXP806 in I2C mode
mfd: axp20x: Add self-working mode support for AXP806
dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806
mfd: wm8994: Allow to configure CS/ADDR Pulldown from dts
mfd: wm8994: Allow to configure Speaker Mode Pullup from dts
mfd: rave-sp: Emulate CMD_GET_STATUS on device that don't support it
mfd: rave-sp: Add legacy watchdog ping command translation
mfd: rave-sp: Add legacy EEPROM access command translation
mfd: rave-sp: Initialize flow control and parity of the port
mfd: rave-sp: Fix incorrectly specified checksum type
mfd: rave-sp: Remove unused defines
mfd: hi655x: Fix regmap area declared size for hi655x
mfd: ti_am335x_tscadc: Fix struct clk memory leak
...
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
