To support vlan and bridge devices first find route using ifindex 0, if
route is not found through net device associated with input scsi host then
find route using ifindex of net device.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If cxgbi_device_find_by_netdev() returns NULL then find cxgbi device by MAC
address.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi_device's refcount is always grabbed in IO path.
Turns out it isn't necessary, because blk_queue_cleanup() will drain any
in-flight IOs, then cancel timeout/requeue work, and SCSI's requeue_work is
canceled too in __scsi_remove_device().
Also scsi_device won't go away until blk_cleanup_queue() is done.
So don't hold the refcount in IO path, especially the refcount isn't
required in IO path since blk_queue_enter() / blk_queue_exit() is
introduced in the legacy block layer.
Cc: Dongli Zhang <dongli.zhang@oracle.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: linux-scsi@vger.kernel.org,
Cc: Martin K . Petersen <martin.petersen@oracle.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: James E . J . Bottomley <jejb@linux.vnet.ibm.com>,
Cc: jianchao wang <jianchao.w.wang@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most but not all code in the qla2xxx driver uses tabs for indentation.
Make the qla2xxx code easier to read by using tabs consistently for
indentation. This patch improves conformance with the Linux kernel coding
style.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we print expander PHY indexes in a mix of decimal and hex.
It is more consistent and also more convenient to read decimal, so
make this change.
We use width of 2 for expander and 1 for root PHYs prints.
Some lines which were needlessly spilling multiple lines are unified.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we discover the PHY is empty in sas_rediscover_dev(), the PHY
information (like negotiated linkrate) is not updated.
As such, for a user examining sysfs for that PHY, they would see
incorrect values:
root@(none)$ cd /sys/class/sas_phy/phy-0:0:20
root@(none)$ more negotiated_linkrate
3.0 Gbit
root@(none)$ echo 0 > enable
root@(none)$ more negotiated_linkrate
3.0 Gbit
So fix this, simply discover the PHY again, even though we know it's empty;
in the above example, this gives us:
root@(none)$ more negotiated_linkrate
Phy disabled
We must do this after unregistering the device associated with the PHY
(in sas_unregister_devs_sas_addr()).
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to the SAS spec, an expander device shall transmit BROADCAST
(CHANGE) from at least one phy in each expander port other than the
expander port that is the cause for transmitting BROADCAST (CHANGE).
As such, for when the link is lost for a root PHY attached to an expander
PHY, we get no broadcast event.
This causes an issue for libsas, in that we will not revalidate the domain
for these events.
As a solution, for when a root PHY is formed or deformed from a root port,
insert a broadcast event to trigger a domain revalidation.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an expander PHY which was part of a wideport disconnects, we would see
a log like this from sas_rediscover():
[ 39.695554] sas: phy20 part of wide port with phy16
Here, phy20 is the PHY that disconnected, and phy16 is the lowest indexed
member PHY of the wideport.
The log implies the phy20 is still part of the wideport with phy16, so is
misleading or, at least, vague.
Improve the logs in SAS rediscovery by removing this log and adding a log
in sas_rediscover_dev() to tell what's really going on.
While we're at it, also make the logs in sas_find_bcast_dev() more
informative (and more consistent with the reset of the expander logs).
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently for fixing the linkrate matching during discovery such that the
linkrate of a SATA PHY does not exceed min pathway to initiator, we set the
SATA PHY programmed min linkrate to the same value as the programmed max
linkrate.
This is unnecessary, and we should be able to keep the same programmed min
linkrate if it is already lower than this new max programmed linkrate.
This patch makes that change.
In effect, this will not make much difference since we generally will
negotiate a linkrate at the programmed max linkrate, and the programmed min
linkrate will have no impact.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many times we use 8 for SAS address length, while we already have a macro
for this - SAS_ADDR_SIZE.
Replace instances of this with the macro. However, don't touch the SAS
address array sizes sas.h, as these are defined according to the SAS spec.
Some missing whitespaces are also added, and whitespace indentation
in sas_hash_addr() is also fixed (see sas_hash_addr()).
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we call hisi_sas_softreset_ata_disk() in
hisi_sas_I_T_nexus_reset().
If this fails for open reject reason, there is no reason to fail the IT
nexus reset, so only fail for TMF_RESP_FUNC_FAILED.
Some other strings spilled over multiple lines are reunited.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the function of hisi_sas_init_device(), we added ops->hardreset() to
clear affiliation of STP target port or handle [STP pending] state.
Function hisi_sas_init_device() will be called when a device is found or
during controller reset. At controller reset, we call
hisi_sas_init_device() to re-init the disks, so calling hardreset() is
unnecessary and it also will cause some delay at controller reset.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is to switch HW all error handling from PCI AER to MSI interrupt
due to non-standard PCI implementation. All HW errors which were being
reported through PCI AER can be reported through MSI interrupt also.
Do two things to complete the switch:
1. Notify FW to switch to MSI handling through ACPI DSM.
2. Add MSI handling for some hw errors, ECC errors and poison errors (we
also call some of them AXI reuser error). They were handled only through
PCI AER before.
For old FW reporting PCI AER events, the PCI AER handler will see that the
driver on longer support AER, and will leave the device in offlined state,
which is safe.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In commit 8b8d665315 ("scsi: hisi_sas: make SAS address of SATA disks
unique"), we ensured that each SATA disk in the system has a unique SAS
address, even if it is fake. That was for v2 hw.
Add this for v3 hw.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function hisi_sas_init_device(), the log is as follows when error for
hardreset:
hisi_sas_v3_hw 0000:74:02.0: SATA disk hardreset fail: 0xffffffed
Actually if hardreset failed, its return value is negative, so change the
print format from %x to %d.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In commit efdcad62e7 ("scsi: hisi_sas: Set PHY linkrate when
disconnected"), we use the sas_phy_data.enable flag to track whether the
PHY was enabled or not, so that we know if we should set the PHY negotiated
linkrate at SAS_LINK_RATE_UNKNOWN or SAS_PHY_DISABLED.
However, it is not proper to use sas_phy_data.enable, since it is only set
when libsas attempts to set the PHY disabled/enabled; hence, it may not
even have an initial value.
As a solution to this problem, introduce hisi_sas_phy.enable to track
whether the PHY is enabled or not, so that we can set the negotiated
linkrate properly when the PHY comes down.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently there are two scenarioes which may cause PHY state of hardware
(which is 0) is inconsistent with the state held in software:
- Unplug SAS wire before get_phys_state when SAS controller reset, then the
interrupts of phy down are ignored, phy state is 0 before reset, and it
also gets 0 after reset, so phy down doesn't occur even if unplugged SAS
wire;
- For v3 hw later version, it will close bus when 2 bit ECC error occurs.
So if unplug SAS wire at that time, interrupts of phy down also not
occur. So at last it will cause host reset. It also get phy state 0
before and after reset, the same issue occurs.
To solve it, use hisi_sas_phy_down() directly in rescan topology function.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We have a few submissions for 5.2 that depend on fixes merged post
5.1-rc1. Merge the fixes branch into queue.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the FC-NVMe driver is leverating the SCSI FC transport class to
access the remote ports. Which means that all FC-NVMe remote ports will be
visible to the fc transport layer, but due to missing definitions the port
roles will always be 'unknown'. This patch adds the missing definitions to
the fc transport class to that the port roles are correctly displayed.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The error return path via label rel_resource checks for a non-null skb
before free'ing it. However, skb is always null at this exit path, so the
null check and the free are redundant and can be removed. Removing this
allows the original goto's to rel_resource to be cleaned up; the first can
be replaced by a return of -EINVAL, the second can be replaced by a more
appropriate -ENOMEM return and fix a memory leak by freeing csk->atid.
Addresses-Coverity: ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If scsi cmd sglist is not suitable for DDP then csiostor driver uses
preallocated buffers for DDP, because of this data copy is required from
DDP buffer to scsi cmd sglist before calling ->scsi_done().
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make sure that resources are only unregistered after the users of these
resources have been unregistered. Only unregister the character device if
registration of it succeeded.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If module initialization fails after the character device has been
registered, unregister the character device. Additionally, avoid
duplicating error path code.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Fixes: 6a03b4cd78 ("[SCSI] qla2xxx: Add char device to increase driver use count") # v2.6.35.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move the SCSI host template definition after the definition of the
functions that it references. Remove the forward declarations that became
unnecessary by that change. This patch does not change any functionality.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make qla2x00_get_host_fabric_name() slightly faster by changing a stack
array into a static array. Declare that array const now that the
wwn_to_u64() argument pointer has been declared const.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support to recognize FPIN ELS's that are received. When
one is received, the fc transport will be called to handle the the FPIN.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a new event type - an FPIN event.
Add a new routine, fc_host_fpin_rcv(), that lldd's call when an FPIN is
received. The routine processes the fpin payload. For now, the routine
only logs an FPIN event.
Signed-off-by: Muneendra <muneendra.kumar@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are two routines generating transport events that do the same thing
with only a couple of values set differently.
Refactor so there's a single routine doing the netlink operations to send
the event. All the differences are passed as arguments. Export the symbol
so the generic routine can be called by llds.
Modify the existing two event routines to use the helper.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the following compiler warning is reported with
CONFIG_NVME_FC=n:
drivers/scsi/lpfc/lpfc_nvme.c:2140:1: warning: 'lpfc_nvme_lport_unreg_wait' defined but not used [-Wunused-function]
lpfc_nvme_lport_unreg_wait(struct lpfc_vport *vport,
^~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 3999df75bc ("scsi: lpfc: Declare local functions static")
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The memory return by kzalloc() has already be set to zero, so remove
useless memset(0).
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
