This allows us to pass dma request lines in platform data to
MMC driver the same way as we already do for omap2430 and later.
Also note that we need to only build this code if MMC_OMAP
is selected, so change Makefile accordingly and place it near
the MMC_OMAP_HS in the Makefile.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull media fixes from Mauro Carvalho Chehab.
Trivial conflict due to new USB HID ID's being added next to each other
(Baanto vs Axentia).
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (44 commits)
[media] smia: Fix compile failures
[media] Fix VIDIOC_DQEVENT docbook entry
[media] s5p-fimc: Fix control creation function
[media] s5p-mfc: Fix checkpatch error in s5p_mfc_shm.h file
[media] s5p-mfc: Fix setting controls
[media] v4l/s5p-mfc: added image size align in VIDIOC_TRY_FMT
[media] v4l/s5p-mfc: corrected encoder v4l control definitions
[media] v4l: mem2mem_testdev: Fix race conditions in driver
[media] s5p-mfc: Bug fix of timestamp/timecode copy mechanism
[media] cxd2820r: Fix an incorrect modulation type bitmask
[media] em28xx: Show a warning if the board does not support remote controls
[media] em28xx: Add remote control support for Terratec's Cinergy HTC Stick HD
[media] USB: Staging: media: lirc: initialize spinlocks before usage
[media] Revert "[media] media: mx2_camera: Fix mbus format handling"
[media] bw-qcam: driver and pixfmt documentation fixes
[media] cx88: fix firmware load on big-endian systems
[media] cx18: support big-endian systems
[media] ivtv: fix support for big-endian systems
[media] tuner-core: return the frequency range of the correct tuner
[media] v4l2-dev.c: fix g_parm regression in determine_valid_ioctls()
...
For a power domain to idle all the clock domains in it must idle.
This patch implements an optimization of the cpuidle code by
denying and later allowing only the first registered clock domain
of a power domain, and so optimizes the latency of the low power code.
The functions _cpuidle_allow_idle and _cpuidle_deny_idle are
not used anymore and so are removed.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
One of the main contributors of the low power code latency is
the PER power domain. To optimize the high-performance and
low-latency C1 state, prevent any PER state which is lower
than the CORE state in C1.
Reported and suggested by Kevin Hilman.
Reported-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
If the next state is no found in the next_valid_state function,
fallback to the default value of C1 (which is state 0).
This prevents the use of a bogus state -1 in the rest of the cpuidle
code.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
commit e7410cf7 (OMAP3: PM: move device-specific special cases from PM
core into CPUidle) moved mangement of cam_pwrdm to CPUidle but left
some remnants behind, namely the call to clkcm_allo_idle() for the
clockdomains in the MPU pwrdm. Remove these since they are not
necessary and cause unwanted latency in the idle path.
Acked-by: Tero Kristo <Tero Kristo <t-kristo@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We only need to call the pre/post transtion methods when we know the
power state is changing. First, split up the pre/post transition
calls to be per-powerdomain, and then make them conditional on whether
the power domain is actually changing states.
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Iteration over all power domains in the idle path is unnecessary since
only power domains that are transitioning need to be accounted for.
Also PRCM register accesses are known to be expensive, so the
additional latency added to the idle path is signficiant.
In order allow the pre/post transitions to be isolated and called
per-pwrdm, change the API so passing in a specific power domain will
trigger the pre/post transtion accounting for only that specific power
domain. Passing NULL means iterating over all power domains as is
current behavior.
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In Tegra30 clock file two clk objects were created for same UART clock.
Remove the duplicates and add clock aliases instead.
Update the Tegra20 clock file to make the names consistent.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
It makes sense to label "Digital Thermal Sensor" as "DTS", but
unfortunately the string "dts" was already used for "Debug Store", and
/proc/cpuinfo is a user space ABI.
Therefore, rename this to "dtherm".
This conflict went into mainline via the hwmon tree without any x86
maintainer ack, and without any kind of hint in the subject.
a4659053 x86/hwmon: fix initialization of coretemp
Reported-by: Jean Delvare <khali@linux-fr.org>
Link: http://lkml.kernel.org/r/4FE34BCB.5050305@linux.intel.com
Cc: Jan Beulich <JBeulich@suse.com>
Cc: <stable@vger.kernel.org> v2.6.36..v3.4
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Convert the OMAP HDQ1W driver to use runtime PM. Make it available on
all OMAP2+ chips that appear to have it integrated. Fix a problem
preventing it from being used on OMAP4.
On SGI's UV2 the BAU (Broadcast Assist Unit) driver can hang
under a heavy load. To cure this:
- Disable the UV2 extended status mode (see UV2_EXT_SHFT), as
this mode changes BAU behavior in more ways then just delivering
an extra bit of status. Revert status to just two meaningful bits,
like UV1.
- Use no IPI-style resets on UV2. Just give up the request for
whatever the reason it failed and let it be accomplished with
the legacy IPI method.
- Use no alternate sending descriptor (the former UV2 workaround
bcp->using_desc and handle_uv2_busy() stuff). Just disable the
use of the BAU for a period of time in favor of the legacy IPI
method when the h/w bug leaves a descriptor busy.
-- new tunable: giveup_limit determines the threshold at which a hub is
so plugged that it should do all requests with the legacy IPI method for a
period of time
-- generalize disable_for_congestion() (renamed disable_for_period()) for
use whenever a hub should avoid using the BAU for a period of time
Also:
- Fix find_another_by_swack(), which is part of the UV2 bug workaround
- Correct and clarify the statistics (new stats s_overipilimit, s_giveuplimit,
s_enters, s_ipifordisabled, s_plugged, s_congested)
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20120622131459.GC31884@sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch enables the BAU to be turned on or off dynamically.
echo "on" > /proc/sgi_uv/ptc_statistics
echo "off" > /proc/sgi_uv/ptc_statistics
The system may be booted with or without the nobau option.
Whether the system currently has the BAU off can be seen in
the /proc file -- normally with the baustats script.
Each cpu will have a 1 in the bauoff field if the BAU was turned
off, so baustats will give a count of cpus that have it off.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20120622131330.GB31884@sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Correct the calculation of a destination timeout period, which
is used to distinguish between a destination timeout and the
situation where all the target software ack resources are full
and a request is returned immediately.
The problem is that integer arithmetic was overflowing, yielding
a very large result.
Without this fix destination timeouts are identified as resource
'plugged' events and an ipi method of resource releasing is
unnecessarily employed.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20120622131212.GA31884@sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The iommu=group_mf is really no longer needed with the addition of ACS
support in IOMMU drivers creating groups. Most multifunction devices
will now be grouped already. If a device has gone to the trouble of
exposing ACS, trust that it works. We can use the device specific ACS
function for fixing devices we trust individually. This largely
reverts bcb71abe.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Implementation of PV EOI using shared memory.
This reduces the number of exits an interrupt
causes as much as by half.
The idea is simple: there's a bit, per APIC, in guest memory,
that tells the guest that it does not need EOI.
We set it before injecting an interrupt and clear
before injecting a nested one. Guest tests it using
a test and clear operation - this is necessary
so that host can detect interrupt nesting -
and if set, it can skip the EOI MSR.
There's a new MSR to set the address of said register
in guest memory. Otherwise not much changed:
- Guest EOI is not required
- Register is tested & ISR is automatically cleared on exit
For testing results see description of previous patch
'kvm_para: guest side for eoi avoidance'.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Each time we need to cancel injection we invoke same code
(cancel_injection callback). Move it towards the end of function using
the familiar goto on error pattern.
Will make it easier to do more cleanups for PV EOI.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Commit eb0dc6d0368072236dcd086d7fdc17fd3c4574d4 introduced apic
attention bitmask but kvm still syncs lapic unconditionally.
As that commit suggested and in anticipation of adding more attention
bits, only sync lapic if(apic_attention).
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
__test_and_clear_bit is actually atomic with respect
to the local CPU. Add a note saying that KVM on x86
relies on this behaviour so people don't accidentaly break it.
Also warn not to rely on this in portable code.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We perform ISR lookups twice: during interrupt
injection and on EOI. Typical workloads only have
a single bit set there. So we can avoid ISR scans by
1. counting bits as we set/clear them in ISR
2. on set, caching the injected vector number
3. on clear, invalidating the cache
The real purpose of this is enabling PV EOI
which needs to quickly validate the vector.
But non PV guests also benefit: with this patch,
and without interrupt nesting, apic_find_highest_isr
will always return immediately without scanning ISR.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
IOMMU-aware dma_alloc_attrs() implementation allocates buffers in
power-of-two chunks to improve performance and take advantage of large
page mappings provided by some IOMMU hardware. However current code, due
to a subtle bug, allocated those chunks in the smallest-to-largest
order, what completely killed all the advantages of using larger than
page chunks. If a 4KiB chunk has been mapped as a first chunk, the
consecutive chunks are not aligned correctly to the power-of-two which
match their size and IOMMU drivers were not able to use internal
mappings of size other than the 4KiB (largest common denominator of
alignment and chunk size).
This patch fixes this issue by changing to the correct largest-to-smallest
chunk size allocation sequence.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Commit f4d40de39a ("net fec: do not depend
on grouped clocks") breaks compilation of the FEC driver for non iMX
platforms in linux-3.5-rc1. For example when compiling for ColdFire I get:
LD vmlinux
drivers/built-in.o: In function `fec_probe':
fec.c:(.devinit.text+0x1e0): undefined reference to `devm_clk_get'
Define a simple devm_clk_get() function for the m68knommu architecture.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas:
ARM: shmobile: r8a7779: Route all interrupts to ARM
ARM: shmobile: kzm9d: use late init machine hook
ARM: shmobile: kzm9g: use late init machine hook
ARM: mach-shmobile: armadillo800eva: Use late init machine hook
ARM: mach-shmobile: add missing GPIO IRQ configuration on mackerel
ARM: mach-shmobile: Fix build when SMP is enabled and EMEV2 is not enabled
ARM: shmobile: sh7372: bugfix: chclr_offset base
ARM: shmobile: sh73a0: bugfix: SY-DMAC number
767c0f3aed
(PM / shmobile: Remove the stay_on flag from SH7372's PM domains)
commit removed sh7372_a3sp_init().
Now, there is no user for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Pull KVM fixes from Avi Kivity:
"Fixing a scheduling-while-atomic bug in the ppc code, and a bug which
allowed pci bridges to be assigned to guests."
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Book3S HV: Drop locks around call to kvmppc_pin_guest_page
KVM: Fix PCI header check on device assignment
Pull ARM SoC fixes from Olof Johansson:
"Nothing very controversial in here. Most of the fixes are for OMAP
this time around, with some orion/kirkwood and a tegra patch mixed in."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: Orion: Fix Virtual/Physical mixup with watchdog
ARM: Kirkwood: clk_register_gate_fn: add fn assignment
ARM: Orion5x - Restore parts of io.h, with rework
ARM: OMAP4: hwmod data: Force HDMI in no-idle while enabled
ARM: OMAP2+: mux: fix sparse warning
ARM: OMAP2+: CM: increase the module disable timeout
ARM: OMAP4: clock data: add clockdomains for clocks used as main clocks
ARM: OMAP4: hwmod data: fix 32k sync timer idle modes
ARM: OMAP4+: hwmod: fix issue causing IPs not going back to Smart-Standby
ARM: OMAP: Fix Beagleboard DVI reset gpio
arm/dts: OMAP2: Fix interrupt controller binding
ARM: OMAP2: Fix tusb6010 GPIO interrupt for n8x0
ARM: OMAP2+: Fix MUSB ifdefs for platform init code
ARM: tegra: make tegra_cpu_reset_handler_enable() __init
ARM: OMAP: PM: Lock clocks list while generating summary
ARM: iconnect: Remove include of removed linux/spi/orion_spi.h
On x86-64, the standard ABI requires alignment to 16 bytes. However,
this is not actually necessary in the kernel (we don't do SSE except
in very controlled ways); and furthermore, the standard kernel entry
on x86-64 actually leaves the stack on an odd 8-byte boundary, which
means that gcc will generate extra instructions to keep the stack
*mis*aligned!
gcc 4.8 adds an -mpreferred-stack-boundary=3 option to override this
and lets us save some stack space and a handful of instructions.
Note that this causes us to pass -mno-sse twice; this is redundant,
but necessary since the cc-option test will fail unless -mno-sse is
passed on the same command line.
[ hpa: rewrote the patch description ]
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Link: http://lkml.kernel.org/r/CAMe9rOqPfy3JcZRLaUeCjBe9BVY-P6e0uaSbMi5hvS-6WwQueg@mail.gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The orion watchdog is expecting to be passed the physcial address of
the hardware, and will ioremap() it to give a virtual address it will
use as the base address for the hardware. However, when creating the
platform resource record, a virtual address was being used.
Add the necassary #define's so we can pass the physical address as
expected.
Tested on Kirkwood and Orion5x.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Olof Johansson <olof@lixom.net>
In commit:
98d9986 ARM: Kirkwood: Replace clock gating
the kirkwood clock gating has been reworked. A custom variant of
clock gating, that calls a custom function before gating the clock
off, has been introduced. However in clk_register_gate_fn() this
custom function "fn" is never assigned.
This patch adds the missing fn assignment.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 4d5fc58dbe (ARM: remove bunch of
now unused mach/io.h files) removed the orion5x io.h. Unfortunately,
this is still needed for the definition of IO_SPACE_LIMIT which
overrides the default 64K. All Orion based systems have 1Mbyte of IO
space per PCI[e] bus, and try to request_resource() this size. Orion5x
has two such PCI buses.
It is likely that the original, removed version, was broken. This
version might be less broken. However, it has not been tested on
hardware with a PCI card, let alone hardware with a PCI card with IO
capabilities.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Paul Walmsley (as per Tony Lindgren's request):
"Some uncontroversial OMAP clock, hwmod, and compiler warning fixes for 3.5-rc"
* tag 'omap-fixes-a-for-3.5rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP4: hwmod data: Force HDMI in no-idle while enabled
ARM: OMAP2+: mux: fix sparse warning
ARM: OMAP2+: CM: increase the module disable timeout
ARM: OMAP4: clock data: add clockdomains for clocks used as main clocks
ARM: OMAP4: hwmod data: fix 32k sync timer idle modes
ARM: OMAP4+: hwmod: fix issue causing IPs not going back to Smart-Standby
ARM: OMAP: PM: Lock clocks list while generating summary
From Tony Lindgren:
"Here are a few fixes with the biggest one being fix for Beagle DVI
reset. All of them are regression fixes, except for the missing omap2
interrupt controller binding that somehow got missed earlier."
* tag 'omap-fixes-for-v3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Fix Beagleboard DVI reset gpio
arm/dts: OMAP2: Fix interrupt controller binding
ARM: OMAP2: Fix tusb6010 GPIO interrupt for n8x0
ARM: OMAP2+: Fix MUSB ifdefs for platform init code
* topic/huang-d3cold-v7:
PCI/PM: add PCIe runtime D3cold support
PCI: do not call pci_set_power_state with PCI_D3cold
PCI/PM: add runtime PM support to PCIe port
ACPI/PM: specify lowest allowed state for device sleep state
PCI subsystem has not been ready for D3cold support yet. So
PCI_D3cold should not be used as parameter for pci_set_power_state.
This patch is needed for upcoming PCI_D3cold support.
This patch has no functionality change, because pci_set_power_state
will bound the parameter to PCI_D3hot too.
CC: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
CC: Jesse Barnes <jesse.barnes@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Without this, the interrupts for I2C, VIN, GPIO, SDHC, HSCIF and
HPB-DMAC are sent to the SH processor.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
ARM builds seem to be plagued by an occasional build error:
Inconsistent kallsyms data
This is a bug - please report about it
Try "make KALLSYMS_EXTRA_PASS=1" as a workaround
The problem has to do with alignment of some sections by the linker.
The kallsyms data is built in two passes by first linking the kernel
without it, and then linking the kernel again with the symbols
included. Normally, this just shifts the symbols, without changing
their order, and the compression used by the kallsyms gives the same
result.
On non SMP, the per CPU data is empty. Depending on the where the
alignment ends up, it can come out as either:
+-------------------+
| last text segment |
+-------------------+
/* padding */
+-------------------+ <- L1_CACHE_BYTES alignemnt
| per cpu (empty) |
+-------------------+
__per_cpu_end:
/* padding */
__data_loc:
+-------------------+ <- THREAD_SIZE alignment
| data |
+-------------------+
or
+-------------------+
| last text segment |
+-------------------+
/* padding */
+-------------------+ <- L1_CACHE_BYTES alignemnt
| per cpu (empty) |
+-------------------+
__per_cpu_end:
/* no padding */
__data_loc:
+-------------------+ <- THREAD_SIZE alignment
| data |
+-------------------+
if the alignment satisfies both. Because symbols that have the same
address are sorted by 'nm -n', the second case will be in a different
order than the first case. This changes the compression, changing the
size of the kallsym data, causing the build failure.
The KALLSYMS_EXTRA_PASS=1 workaround usually works, but it is still
possible to have the alignment change between the second and third
pass. It's probably even possible for it to never reach a fixedpoint.
The problem only occurs on non-SMP, when the per-cpu data is empty,
and when the data segment has alignment (and immediately follows the
text segments). Fix this by only including the per_cpu section on
SMP, when it is not empty.
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* topic/jiang-mmconfig-v10:
ACPI: mark acpi_sfi_table_parse() as __init
x86/PCI: use pr_level() to replace printk(KERN_LEVEL)
x86/PCI: refine __pci_mmcfg_init() for better code readability
x86/PCI: get rid of redundant log messages
x86/PCI: simplify pci_mmcfg_late_insert_resources()
x86/PCI: update MMCONFIG information when hot-plugging PCI host bridges
PCI/ACPI: provide MMCONFIG address for PCI host bridges
x86/PCI: add pci_mmconfig_insert()/delete() for PCI root bridge hotplug
x86/PCI: prepare pci_mmcfg_check_reserved() to be called at runtime
x86/PCI: introduce pci_mmcfg_arch_map()/pci_mmcfg_arch_unmap()
x86/PCI: use RCU list to protect mmconfig list
x86/PCI: split out pci_mmconfig_alloc() for code reuse
x86/PCI: split out pci_mmcfg_check_reserved() for code reuse
Script checkpatch.pl recommends to replace printk(KERN_LVL) with pr_lvl(),
so do it.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
For each resource of a PCI host bridge, the arch code and PCI
code log following messages. We don't need both, so drop the
arch-specific printing.
pci_root PNP0A08:00: host bridge window [io 0x0000-0x03af]
pci_bus 0000:00: root bus resource [io 0x0000-0x03af]
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
