Add support for the IB-NAS6210 and IB-NAS 6220. Describe as much as
currently possible in the devicetree files, including the NAND partitions.
Use the partition scheme of the original firmware by default.
Create a board-ib62x0.c for everything else.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The maxburst/chunk size was taken from the private slave DMA data structure.
Use the common API provided by DMA_SLAVE_CONFIG to setup src/dst maxburst
values.
The ctrla field is not needed anymore in the slave private structure nor the
header constants that were located in an architecture specific directory.
The at91sam9g45_devices.c file that was using this platform data is also
modified to remove this now useless data.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
dns323 and (at least) iconnect platforms are using hw led blinking, so,
instead of having 2 identicals .gpio_blink_set gpio-led hooks, move
dns323 code into gpio.c
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-By: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
gpio registers are for 32 gpios. Given that orion_gpio_set_blink is called
directly and not through gpiolib, it needs to make sure that the pin value
given to the internal functions are between 0 and 31.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-By: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Use devicetree to define NAND partitions. Use D-link partition scheme by
default, to be vaguely compatible with their userland.
Changes since last submission (V4):-
* Don't add NAND support then throw it away immediately after [Grant Likely]
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add default configuration for NAND, to be enabled in your board config. Ensure
clock gating is set appropriately when the NAND is enabled.
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add support for the DNS-320 and DNS-325. Describe as much as currently possible
in the devicetree files, create a board-dnskw.c for everything else.
Changes since last submission (V3) [Addressing comments by]:-
* One MACH_DLINK_KIRKWOOD_DT for all dtb files [Grant Likely, Jason Cooper]
* Drop brain-dead select "select CONFIG_MTD_OF_PARTS" [Grant Likely]
* Don't add NAND support then throw it away immediately after [Grant Likely]
* Describe purpose of MPP 41, 42 & 49
Changes since last submission (V2):-
* Use IEEE-compliant "okay", rather than "ok" [Scott Wood]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Section 15.3.1.2 of the software developer manual has this to say about the
RIPV bit in the IA32_MCG_STATUS register:
RIPV (restart IP valid) flag, bit 0 — Indicates (when set) that program
execution can be restarted reliably at the instruction pointed to by the
instruction pointer pushed on the stack when the machine-check exception
is generated. When clear, the program cannot be reliably restarted at
the pushed instruction pointer.
We need to save the state of this bit in do_machine_check() and use it
in mce_notify_process() to force a signal; even if memory_failure() says
it made a complete recovery ... e.g. replaced a clean LRU page.
Acked-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Use DT_MACHINE_START() on the r8a7740 based armadillo 800 eva board.
Also include a tiny DTS file to describe the board and update the
Kconfig dependencies to select CONFIG_USE_OF.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Use DT_MACHINE_START() on the sh73a0 based KZM9G board.
Also include a tiny DTS file to describe the board and
update the Kconfig dependencies to select CONFIG_USE_OF.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since percpu_xxx() serial functions are duplicated with this_cpu_xxx().
Removing percpu_xxx() definition and replacing them by this_cpu_xxx()
in code. There is no function change in this patch, just preparation for
later percpu_xxx serial function removing.
On x86 machine the this_cpu_xxx() serial functions are same as
__this_cpu_xxx() without no unnecessary premmpt enable/disable.
Thanks for Stephen Rothwell, he found and fixed a i386 build error in
the patch.
Also thanks for Andrew Morton, he kept updating the patchset in Linus'
tree.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Acked-by: Christoph Lameter <cl@gentwo.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
- remove all uses of btfixup header
- remove the btfixup header
- remove the btfixup code
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use sparc_config to hold the last two function pointers. There was no
point generating dedicated _ops structures only for these.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I ended up renaming set_cpu_int to send_ipi to
be consistent all way around.
send_ipi was moved to the *_smp.c files so
we could call the relevant method direct,
without any _ops indirection.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the last non-trivial user of btfixup.
Like sparc64, use a special patch section to resolve the various
implementations of how to read the current CPU's ID when we don't
have current_thread_info()->cpu necessarily available.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Sam Ravnborg <sam@ravnborg.org>
Stephen Warren <swarren@wwwdotorg.org> writes:
This branch is based on the merge of the following branches from the
Tegra repo, which are all already pulled into arm-soc:
for-3.5/tegra30-audio
for-3.5/usb-ulpi
for-3.5/dt
... which are all based on for-3.5/gpio-pinmux
* 'for-3.5/dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: dt: tegra: invert status=disable vs status=okay
ARM: dt: tegra: consistent basic property ordering
ARM: dt: tegra: sort nodes based on bus order
ARM: dt: tegra: remove duplicate device_type property
ARM: dt: tegra: consistenly use lower-case for hex constants
ARM: dt: tegra: format regs properties consistently
ARM: dt: tegra: gpio comment cleanup
ARM: dt: tegra: remove unnecessary unit addresses
ARM: dt: tegra: whitespace cleanup
ARM: dt: tegra cardhu: fix typo in SDHCI node name
ARM: dt: tegra: cardhu: register core regulator tps62361
ARM: dt: tegra30.dtsi: Add SMMU node
ARM: dt: tegra20.dtsi: Add GART node
ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra: Add device tree support for AHB
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Kukjin Kim <kgene.kim@samsung.com> writes:
As there were discussions, some exynos4 boards have been updated because
current dt cannot support all features for current board files on
exynos4.
Note, this should be merged after next/devel-samsung because some
platform devices are defined in that.
* 'next/board-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add FIMC device to SMDK4X12
ARM: EXYNOS: Add MFC device to SMDK4X12
ARM: EXYNOS: Add DRM device to SMDKV310
ARM: EXYNOS: Add DRM device to Origen
ARM: EXYNOS: Make BT platform data structure static in mach-origen.c file
ARM: EXYNOS: Add DRM core support for NURI board
ARM: EXYNOS: Add DRM core device support for Universal C210 board
ARM: EXYNOS: Increase framebuffer virtual size for origen
ARM: S3C64XX: Hook up new style regulator-regulator supplies on Cragganmore
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The omap/dt branch adds a few instances of mmc device nodes that
need to get changed to use the common bindings. Pull that into
a new branch so we can apply the patch in a single run.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'dt' of git://github.com/hzhuang1/linux:
Documentation: update docs for mmp dt
ARM: dts: refresh dts file for arch mmp
ARM: mmp: support pxa910 with device tree
ARM: mmp: support mmp2 with device tree
gpio: pxa: parse gpio from DTS file
ARM: mmp: support DT in timer
ARM: mmp: support DT in irq
ARM: mmp: append CONFIG_MACH_MMP2_DT
ARM: mmp: fix build issue on mmp with device tree
Includes an update to v3-4-rc5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Kukjin Kim <kgene.kim@samsung.com> writes:
We can remove plat-s5p directory with this series and I think, the
plat-s3c24xx can be removed next time for one plat-samsung of Samsung
stuff.
Note, this is including cleanup-samsung-iommu which is removing s5p
iommu stuff in plat-s5p.
* 'next/cleanup-plat-s3c24xx-s5p' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: merge plat-s5p into plat-samsung
ARM: SAMSUNG: move options for common s5p into plat-samsung/Kconfig
ARM: SAMSUNG: move setup code for s5p mfc and mipiphy into plat-samsung
ARM: SAMSUNG: move platform device for s5p uart into plat-samsung
ARM: SAMSUNG: move hr timer for common s5p into plat-samsung
ARM: SAMSUNG: move pm part for common s5p into plat-samsung
ARM: SAMSUNG: move interrupt part for common s5p into plat-samsung
ARM: SAMSUNG: move clock part for common s5p into plat-samsung
ARM: S3C24XX: Use common macro to define resources on dev-uart.c
ARM: S3C24XX: move common clock init into common.c
ARM: S3C24XX: move common power-management code to mach-s3c24xx
ARM: S3C24XX: move plat-s3c24xx/dev-uart.c into common.c
ARM: S3C24XX: move plat-s3c24xx/cpu.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All functions from this header already provided by common.c
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ep7312 has been supported for a very long time, but has never
been mentioned in the Kconfig file.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is no reason to have the clps7111.h header in a globally
visible location, so move it to a place that is only visible when
building for mach-clps711x.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In tegra*.dtsi, set status="disable" for all HW modules that the board
design may choose not to use. Update all boards to specifically enable
any of those modules that are useful by setting status="okay".
This makes board files say which features they do use, rather than which
they don't, which feels more logical. It also makes the .dts files
slightly smaller, at least for existing content.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Put properties in order compatible, reg, interrupts, then anything else
the node has.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Sort the nodes according to the following rules:
* First, any overrides for properties or nodes created by included files,
in the order they appeared in the include file.
* Second, any nodes with a reg property, in numerical order.
* Third, any nodes without a reg property, in alphabetical order of node
name.
The second sorting rule at least will probably help if/when we need to
explicitly insert nodes for the various busses in Tegra; that will just
be an indentation change rather than also a node re-ordering.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
It's already specified in skeleton.dtsi, included via tegra20.dtsi.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
