Pull ARM SoC fixes for SPEAr from Olof Johansson:
"These are arriving very late in the release cycle, but there has been
a change of maintainers on the SPEAr platform and they have needed a
while to get going.
The patch count is higher than I would like at this point, but they're
all relevant fixes and well-contained in their own platform code. I
still think it's suitable 3.5 material and I don't think it should
increase the need for a -rc8 since they are so contained."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: SPEAr600: Fix timer interrupt definition in spear600.dtsi
ARM: dts: SPEAr320: Boot the board in EXTENDED_MODE
ARM: dts: SPEAr320: Fix compatible string
Clk: SPEAr1340: Update sys clock parent array
clk: SPEAr1340: Fix clk enable register for uart1 and i2c1.
ARM: SPEAr13xx: Fix Interrupt bindings
Clk:spear6xx:Fix: Rename clk ids within predefined limit
Clk:spear3xx:Fix: Rename clk ids within predefined limit
clk:spear1310:Fix: Rename clk ids within predefined limit
clk:spear1340:Fix: Rename clk ids within predefined limit
On spear320 device supported mode are:
* AUTO_NET_SMII_MODE
* AUTO_NET_MII_MODE
* AUTO_EXP_MODE
* SMALL_PRINTERS_MODE
* EXTENDED_MODE
spear320-evb board is designed for EXTENDED_MODE only, hence it does not
boot correctly in current form where pinctrl part for some devices fail.
Configure and boot the SPEAr320 evaluation board in EXTENDED_MODE.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The max limit of con_id is 16 and dev_id is 20. As of now for spear6xx, many clk
ids are exceeding this predefined limit.
This patch is intended to rename clk ids like:
mux_clk -> _mclk
gate_clk -> _gclk
synth_clk -> syn_clk
ras_gen1_synth_gate_clk -> ras_syn1_gclk
pll3_48m -> pll3_
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The max limit of con_id is 16 and dev_id is 20. As of now for spear3xx, many clk
ids are exceeding this predefined limit.
This patch is intended to rename clk ids like:
mux_clk -> _mclk
gate_clk -> _gclk
synth_clk -> syn_clk
ras_gen1_synth_gate_clk -> ras_syn1_gclk
ras_pll3_48m -> ras_pll3_
pll3_48m -> pll3_
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Pull CMA and DMA-mapping fixes from Marek Szyprowski:
"Another set of minor fixups for recently merged Contiguous Memory
Allocator and ARM DMA-mapping changes. Those patches fix mysterious
crashes on systems with CMA and Himem enabled as well as some corner
cases caused by typical off-by-one bug."
* 'fixes-for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: modify condition check while freeing pages
mm: cma: fix condition check when setting global cma area
mm: cma: don't replace lowmem pages with highmem
WARNING: at mm/vmalloc.c:1471 __iommu_free_buffer+0xcc/0xd0()
Trying to vfree() nonexistent vm area (ef095000)
Modules linked in:
[<c0015a18>] (unwind_backtrace+0x0/0xfc) from [<c0025a94>] (warn_slowpath_common+0x54/0x64)
[<c0025a94>] (warn_slowpath_common+0x54/0x64) from [<c0025b38>] (warn_slowpath_fmt+0x30/0x40)
[<c0025b38>] (warn_slowpath_fmt+0x30/0x40) from [<c0016de0>] (__iommu_free_buffer+0xcc/0xd0)
[<c0016de0>] (__iommu_free_buffer+0xcc/0xd0) from [<c0229a5c>] (exynos_drm_free_buf+0xe4/0x138)
[<c0229a5c>] (exynos_drm_free_buf+0xe4/0x138) from [<c022b358>] (exynos_drm_gem_destroy+0x80/0xfc)
[<c022b358>] (exynos_drm_gem_destroy+0x80/0xfc) from [<c0211230>] (drm_gem_object_free+0x28/0x34)
[<c0211230>] (drm_gem_object_free+0x28/0x34) from [<c0211bd0>] (drm_gem_object_release_handle+0xcc/0xd8)
[<c0211bd0>] (drm_gem_object_release_handle+0xcc/0xd8) from [<c01abe10>] (idr_for_each+0x74/0xb8)
[<c01abe10>] (idr_for_each+0x74/0xb8) from [<c02114e4>] (drm_gem_release+0x1c/0x30)
[<c02114e4>] (drm_gem_release+0x1c/0x30) from [<c0210ae8>] (drm_release+0x608/0x694)
[<c0210ae8>] (drm_release+0x608/0x694) from [<c00b75a0>] (fput+0xb8/0x228)
[<c00b75a0>] (fput+0xb8/0x228) from [<c00b40c4>] (filp_close+0x64/0x84)
[<c00b40c4>] (filp_close+0x64/0x84) from [<c0029d54>] (put_files_struct+0xe8/0x104)
[<c0029d54>] (put_files_struct+0xe8/0x104) from [<c002b930>] (do_exit+0x608/0x774)
[<c002b930>] (do_exit+0x608/0x774) from [<c002bae4>] (do_group_exit+0x48/0xb4)
[<c002bae4>] (do_group_exit+0x48/0xb4) from [<c002bb60>] (sys_exit_group+0x10/0x18)
[<c002bb60>] (sys_exit_group+0x10/0x18) from [<c000ee80>] (ret_fast_syscall+0x0/0x30)
This patch modifies the condition while freeing to match the condition
used while allocation. This fixes the above warning which arises when
array size is equal to PAGE_SIZE where allocation is done using kzalloc
but free is done using vfree.
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Pull ARM Samsung SoC fixes from Arnd Bergmann.
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: S3C24XX: Correct CAMIF interrupt definitions
ARM: S3C24XX: Correct AC97 clock control bit for S3C2440
ARM: SAMSUNG: fix race in s3c_adc_start for ADC
ARM: SAMSUNG: Update default rate for xusbxti clock
ARM: EXYNOS: register devices in 'need_restore' state for pm_domains
ARM: EXYNOS: read initial state of power domain from hw registers
Properly define the CAMIF interrupt resources. This device have two
interrupts - corresponding to the "codec" and "preview" data paths.
IRQ_CAM is handled internally by the architecture and demultiplexed
to IRQ_S3C2440_CAM_C and IRQ_S3C2440_CAM_P - these interrupts only
should be handled in the driver.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use correct gate control bit for AC97 clock which is
S3C2440_CLKCON_AC97, not S3C2440_CLKCON_CAMERA.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The rate of xusbxti clock is set in individual machine files.
The default value should be defined at the clock definition
and individual machine files should modify it if required.
Division by zero in kernel.
[<c0011849>] (unwind_backtrace+0x1/0x9c) from [<c022c663>] (Ldiv0+0x9/0x12)
[<c022c663>] (Ldiv0+0x9/0x12) from [<c001a3c3>] (s3c_setrate_clksrc+0x33/0x78)
[<c001a3c3>] (s3c_setrate_clksrc+0x33/0x78) from [<c0019e67>] (clk_set_rate+0x2f/0x78)
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Commit ca1d72f033 ('PM / Domains: Make it possible to add devices to
inactive domains') introduced possibility to add devices to inactive
power domains and added pm_genpd_dev_need_restore() function which lets
platform core to notify power domain core that the specified device must
be restored (with its runtime_resume() callback) before first use.
This patch adds the pm_genpd_dev_need_restore() call what brings back
the suspend/resume behaviour for the client devices known from the
previous power domain driver (removed by commit 91cfbd4ee0 - 'ARM:
EXYNOS: Hook up power domains to generic power domain infrastructure').
Client device drivers relay on that suspend/resume behaviour, thus this
patch fixes runtime pm operation for client devices.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Some bootloaders disable unused power domains to reduce power
consuption. Power domain driver can easily read the actual state from
the hardware registers instead of assuming that their initial state is
always 'on'.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pull ARM SoC fixes from Arnd Bergmann:
- multiple omap2+ bug fixes
- a regression on ux500 dt support
- a build failure on shmobile
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP2+: omap2plus_defconfig: EHCI driver is not stable, disable it
ARM: shmobile: fix platsmp.c build when ARCH_SH73A0=n
ARM: ux500: Over-ride the DT device naming scheme for pinctrl
ARM: ux500: Fix build errors/warnings when MACH_UX500_DT is not set
of: address: Don't fail a lookup just because a node has no reg property
ARM: OMAP2+: hwmod code/clockdomain data: fix 32K sync timer
From Tony Lindgren <tony@atomide.com>:
Here is one PM regression fix and a defconfig change to disable
echi-omap because the driver currently causes issues with PM.
This annoys Kevin as it makes it harder for him to validate that
PM is working. The proper fixes for the echi-omap are being
discussed, but looks like it will not be properly working with PM
until in v3.7.
* tag 'omap-fixes-for-v3.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap2plus_defconfig: EHCI driver is not stable, disable it
ARM: OMAP2+: hwmod code/clockdomain data: fix 32K sync timer
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The EHCI driver is not stable enough to be enabled by default. In v3.5,
it has at least the following problems:
- warning dump during bootup
- hang during suspend
- prevents CORE powerdomain from entering retention during idle (even
when no USB devices connected.)
This demonstrates that this driver has not been thoroughly tested and
therfore should not be enabled in the default defconfig.
In addition, the problems above cause new PM regressions which need be
addressed before this driver should be enabled in the default
defconfig.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull ARM fixes from Russell King:
"Last merge window, we had some updates from Al cleaning up the signal
restart handling. These have caused some problems on ARM, and while
Al has some fixes, we have some concerns with Al's patches but we've
been unsuccesful with discussing this.
We have got to the point where we need to do something, and we've
decided that the best solution is to revert the appropriate commits
until Al is able to reply to us.
Also included here are four patches to fix warnings that I've noticed
in my build system, and one fix for kprobes test code."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: fix warning caused by wrongly typed arm_dma_limit
ARM: fix warnings about atomic64_read
ARM: 7440/1: kprobes: only test 'sub pc, pc, #1b-2b+8-2' on ARMv6
ARM: 7441/1: perf: return -EOPNOTSUPP if requested mode exclusion is unavailable
ARM: 7443/1: Revert "new way of handling ERESTART_RESTARTBLOCK"
ARM: 7442/1: Revert "remove unused restart trampoline"
ARM: fix set_domain() macro
ARM: fix mach-versatile/pci.c warning
Fix build error in the case of SMP=y but ARCH_SH73A0=n
introduced by:
9601e87 ARM: shmobile: fix smp build
The use of of_machine_is_compatible() will link in the
the SoC-specific symbols:
"sh73a0_get_core_count", "sh73a0_smp_prepare_cpus",
"sh73a0_secondary_init" and "sh73a0_boot_secondary".
This patch adds an ugly #ifdef wrapper as a stop-gap
solution.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Lee Jones <lee.jones@linaro.org>:
* ux500/fixes-3.5:
ARM: ux500: Over-ride the DT device naming scheme for pinctrl
ARM: ux500: Fix build errors/warnings when MACH_UX500_DT is not set
of: address: Don't fail a lookup just because a node has no reg property
I ended up rebasing Lee's branch on 3.5-rc5 because we have more patches
lined for 3.6 that depend on them, and I want to keep all branches in
arm-soc be based on -rc releases rather than random commits in the
upstream history.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When pin control mapping tables are written the registered device
name is supplied for use in name-based searches within the pinctrl
driver. In the case of the DB8500 the string "pinctrl-db8500" is
used. However, when we register the driver with Device Tree, its
naming convention uses something that looks more like "pinctrl.2".
To work around the device naming inconsistencies between devices
registered via platform code and the ones registered by Device
Tree, we use AUXDATA to over-ride the Device Tree naming scheme.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When MACH_UX500_DT and all related Device Tree configurations are forced
off the warning and error below prevent the kernel from compiling. This
simple patch fixes both issues and allows for full build and boot of
ST-Ericsson's low-cost development board, Snowball.
Warnings fixed:
arch/arm/mach-ux500/board-mop500.c:680:32: warning: ‘snowball_of_platform_devs’ defined but not used
Errors fixed:
arch/arm/mach-ux500/timer.c: In function ‘ux500_timer_init’:
arch/arm/mach-ux500/timer.c:66:3: error: implicit declaration of function ‘of_find_matching_node’
arch/arm/mach-ux500/timer.c:66:6: warning: assignment makes pointer from integer without a cast
Cc: stable@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Kevin discovered that commit c8d82ff68f
("ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod
database") broke CORE idle on OMAP3. This prevents device low power
states.
The root cause is that the 32K sync timer IP block does not support
smart-idle mode[1], and so the hwmod code keeps the IP block in
no-idle mode while it is active. This in turn prevents the WKUP
clockdomain from transitioning to idle. There is a hardcoded sleep
dependency that prevents the CORE_L3 and CORE_CM clockdomains from
transitioning to idle when the WKUP clockdomain is active[2], so the
chip cannot enter any device low power states.
It turns out that there is no need to take the 32k sync timer out of
idle. The IP block itself probably does not have any native idle
handling at all, due to its simplicity. Furthermore, the PRCM will
never request target idle for this IP block while the kernel is
running, due to the sleep dependency that prevents the WKUP
clockdomain from idling while the CORE_L3 clockdomain is active. So
we can safely leave the 32k sync timer in target-force-idle mode, even
while we continue to access it.
This workaround is implemented by defining a new clockdomain flag,
CLKDM_ACTIVE_WITH_MPU, that indicates that the clockdomain is
guaranteed to be active whenever the MPU is inactive. If an IP
block's main functional clock exists inside this clockdomain, and the
IP block does not support smart-idle modes, then the hwmod code will
place the IP block into target force-idle mode even when enabled. The
WKUP clockdomains on OMAP3/4 are marked with this flag. (On OMAP2xxx,
no OCP header existed on the 32k sync timer.) Other clockdomains also
should be marked with this flag, but those changes are deferred until
a later merge window, to create a minimal fix.
Another theoretically clean fix for this problem would be to implement
PM runtime-based control for 32k sync timer accesses. These PM
runtime calls would need to located in a custom clocksource, since the
32k sync timer is currently used as an MMIO clocksource. But in
practice, there would be little benefit to doing so; and there would
be some cost, due to the addition of unnecessary lines of code and the
additional CPU overhead of the PM runtime and hwmod code - unnecessary
in this case.
Another possible fix would have been to modify the pm34xx.c code to
force the IP block idle before entering WFI. But this would not have
been an acceptable approach: we are trying to remove this type of
centralized IP block idle control from the PM code.
This patch is a collaboration between Kevin Hilman <khilman@ti.com>
and Paul Walmsley <paul@pwsan.com>.
Thanks to Vaibhav Hiremath <hvaibhav@ti.com> for providing comments on
an earlier version of this patch. Thanks to Tero Kristo
<t-kristo@ti.com> for identifying a bug in an earlier version of this
patch. Thanks to Benoît Cousson <b-cousson@ti.com> for identifying
some bugs in several versions of this patch and for implementation
comments.
References:
1. Table 16-96 "REG_32KSYNCNT_SYSCONFIG" of the OMAP34xx TRM Rev. ZU
(SWPU223U), available from:
http://www.ti.com/pdfs/wtbu/OMAP34x_ES3.1.x_PUBLIC_TRM_vzU.zip
2. Table 4-72 "Sleep Dependencies" of the OMAP34xx TRM Rev. ZU
(SWPU223U)
3. ibid.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Pull ARM SoC fixes from Arnd Bergmann:
"Small fixes on multiple ARM platforms
- A build regression from a previous fix on dove and mv78xx0
- Two fixes for recently (3.5-rc1) changed mmp/pxa code
- multiple omap2+ bug fixes
- two trivial fixes for i.MX
- one v3.5 regression for mxs"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: apx4devkit: fix FEC enabling PHY clock
ARM: OMAP2+: hwmod data: Fix wrong McBSP clock alias on OMAP4
ARM: OMAP4: hwmod data: temporarily comment out data for the usb_host_fs and aess IP blocks
ARM: Orion: Fix WDT compile for Dove and MV78xx0
ARM: mmp: remove mach/gpio-pxa.h
ARM: imx: assert SCC gate stays enabled
ARM: OMAP4: TWL6030: ensure sys_nirq1 is mux'd and wakeup enabled
ARM: OMAP2: Overo: init I2C before MMC to fix MMC suspend/resume failure
ARM: imx27_visstrim_m10: Do not include <asm/system.h>
ARM: pxa: hx4700: Fix basic suspend/resume
arch/arm/mm/init.c: In function 'arm_memblock_init':
arch/arm/mm/init.c:380: warning: comparison of distinct pointer types lacks a cast
by fixing the typecast in its definition when DMA_ZONE is disabled.
This was missed in 4986e5c7c (ARM: mm: fix type of the arm_dma_limit
global variable).
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
net/netfilter/xt_connbytes.c: In function 'connbytes_mt':
net/netfilter/xt_connbytes.c:43: warning: passing argument 1 of 'atomic64_read' discards qualifiers from pointer target type
...
by adding the missing const.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
'sub pc, pc, #1b-2b+8-2' results in address<1:0> == '10'.
sub pc, pc, #const (== ADR pc, #const) performs an interworking branch
(BXWritePC()) on ARMv7+ and a simple branch (BranchWritePC()) on earlier
versions.
In ARM state, BXWritePC() is UNPREDICTABLE when address<1:0> == '10'.
In ARM state on ARMv6+, BranchWritePC() ignores address<1:0>. Before
ARMv6, BranchWritePC() is UNPREDICTABLE if address<1:0> != '00'
So the instruction is UNPREDICTABLE both before and after v6.
Acked-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PM related fixes for omaps mostly to get suspend/resume
working again.
* tag 'omap-fixes-for-v3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: hwmod data: Fix wrong McBSP clock alias on OMAP4
ARM: OMAP4: hwmod data: temporarily comment out data for the usb_host_fs and aess IP blocks
ARM: OMAP4: TWL6030: ensure sys_nirq1 is mux'd and wakeup enabled
ARM: OMAP2: Overo: init I2C before MMC to fix MMC suspend/resume failure
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We currently return -EPERM if the user requests mode exclusion that is
not supported by the CPU. This looks pretty confusing from userspace
and is inconsistent with other architectures (ppc, x86).
This patch returns -EOPNOTSUPP instead.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 6b5c8045ec.
Conflicts:
arch/arm/kernel/ptrace.c
The new syscall restarting code can lead to problems if we take an
interrupt in userspace just before restarting the svc instruction. If
a signal is delivered when returning from the interrupt, the
TIF_SYSCALL_RESTARTSYS will remain set and cause any syscalls executed
from the signal handler to be treated as a restart of the previously
interrupted system call. This includes the final sigreturn call, meaning
that we may fail to exit from the signal context. Furthermore, if a
system call made from the signal handler requires a restart via the
restart_block, it is possible to clear the thread flag and fail to
restart the originally interrupted system call.
The right solution to this problem is to perform the restarting in the
kernel, avoiding the possibility of handling a further signal before the
restart is complete. Since we're almost at -rc6, let's revert the new
method for now and aim for in-kernel restarting at a later date.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avoid polluting drivers with a set_domain() macro, which interferes with
structure member names:
drivers/net/wireless/ath/ath9k/dfs_pattern_detector.c:294:33: error: macro "set_domain" passed 2 arguments, but takes just 1
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-versatile/pci.c: In function 'versatile_map_irq':
arch/arm/mach-versatile/pci.c:342: warning: unused variable 'devslot'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The commit 503d0ea24d
ARM: OMAP4: hwmod data: Add aliases for McBSP fclk clocks
added a wrong "prcm_clk" alias for PRCM clock whereas the McBSP
driver and previous OMAPs are using "prcm_fck".
It thus lead to the following warning.
[ 47.409729] omap-mcbsp: clks: could not clk_get() prcm_fck
Fix that by changing the opt_clk role to prcm_fck.
Reported-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP4 usb_host_fs (OHCI) and AESS IP blocks require some special
programming for them to enter idle. Without this programming, they
will prevent the rest of the chip from entering full chip idle.
To implement the idle programming cleanly, this will take some
coordination between maintainers. This is likely to take some time,
so it is probably best to leave this for 3.6 or 3.7. So, in the
meantime, prevent these IP blocks from being registered.
Later, once the appropriate support is available, this patch can be
reverted.
This second version comments out the IP block data since Benoît didn't
like removing it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
From Sascha Hauer <s.hauer@pengutronix.de>:
ARM i.MX fixes for v3.5-rc5
* tag 'v3.5-imx-fixes' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: imx: assert SCC gate stays enabled
ARM: imx27_visstrim_m10: Do not include <asm/system.h>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 0fa1f0609a (ARM: Orion: Fix
Virtual/Physical mixup with watchdog) broke the Dove & MV78xx0
build. Although these two SoC don't use the watchdog, the shared
platform code still needs to build. Add the necessary defines.
Cc: stable@vger.kernel.org
Reported-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 157d2644cb ("ARM: pxa: change gpio
to platform device") removed all includes of mach/gpio-pxa.h. It kept
this unused header in the tree. Using it can't work, as it itself
includes the non-existent header plat/gpio-pxa.h. This header can safely
be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
The SCC clock is needed in internal boot mode and so must keep enabled.
This same issue was fixed for the pre-common-clk code in commit
3d6e614 (mx35: Fix boot ROM hang in internal boot mode)
Cc: John Ogness <jogness@linutronix.de>
Cc: Hans J. Koch <hjk@hansjkoch.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The SYS_NIRQ1 pin is the interupt line for the PMIC part of the TWL6030
and interrupts from the PMIC are needed as wakeup sources.
Ensure this pin is mux'd as input and has wakeup enabled so PMIC
interupts (e.g. RTC) can be used as wakeup sources.
Tested on OMAP4430/Panda.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order for suspend/resume dependencies to work correctly, I2C has to
be initialized (more specifically, registered with the driver core)
before MMC. Without this, the MMC driver fails to adjust the VMMC
regulator (using i2c writes) during the suspend path.
Problem found testing suspend/resume on 3730/OveroSTORM platform.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit 435ca24 (ARM i.MX: Visstrim_M10: Add board version detection)
included <asm/system.h>, which is a header file about to be deleted according to
9f97da (Disintegrate asm/system.h for ARM)
Include <asm/system_info.h> instead.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
