Add struct size checks to many of the indirect structs and a few
command structs that were left out previously.
Change-ID: I7810b9af0f04e3ced670639f8671daf7df9b3f4d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Disable firmware LLDP agent for NICs with firmware version lower than
v4.3. Added a message when driver disables the firmware LLDP agent on
such NICs.
Change-ID: Ia8abf89439c70cb50e23db82753d7d282265506b
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We should not be doing Tx or Rx timestamps if we do not have PTP
enabled. Add checks to ensure that we don't attempt to handle any PTP
related timestamping code if we have not enabled PTP on that PF.
Change-ID: I4335942ae2d5c5f91abfdbeeea02bcace49e7677
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We should not blindly enable the PTP interrupt flags for all PFs. We
should only enable the PTP interrupt in PFs which have enabled
PTP.
Change-ID: I051a17cae4c199a2f3cf7852266e27eda6630525
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dump Stats string has been removed from functional debugfs
help message. Now it does not show up when we echo command to
debugfs/Fortville queue.
Change-ID: I9333473826b574f1afa6ddb785fd7adfbdcb2884
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch creates a define for interrupt name string configuration that
is large enough to contain full bus/slot info, rather than just netdev->name.
Change-ID: Iaac0d23dfb8526defeed69d91cea85ed4a50ddb2
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need to give up in the reset/rebuild process if the DCB setup failed,
so handle it here the same as in the probe setup. Also adjust the log strings
a little to look less scary.
Change-ID: I57308d703047e61d3f1a5e471ea77be232444ca0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where the /proc/interrupts descriptions
from the msix configuration were truncating the needed bus info,
making it hard to distinguish configuration from port to port.
This patch increases the string buffer size in order to allow the
full data to be displayed and sync's the text formatting of the misc
and fdir interrupt names
Change-ID: Ib01d6c61fb3f4ac70fbdf5bcc520b22638ea54b7
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Increase ASQ timeout for some scenarios with multi-function devices
Change-ID: I2d7655b19e6c6f9a7ad04deacb106ca8d53886db
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several little tweaks to keep FW, SV, and SW in line together
- Remove the unused and deprecated
i40e_aqc_opc_debug_modify_internals
- Add define for iSCSI capability
- Fix queue mask size
- Adjust i40e_aqc_oem_param_change for ease-of-use
Change-ID: I51f250b367912968a7cec61b3a68110d9796e914
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Kamil Kacperski <kamil.kacperski@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
10/100 MACB does not have the same statistics possibilities as GEM. Separate
macb_ethtool_ops to make a new GEM-specific struct with the new statistics
functions included.
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spaces should surround add, multiply, and bitshift operators.
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change comments to not exceed 80 characters per line.
Update block comments in macb.h to start on the line after /*.
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Atari specific code to the smc91x Ethernet driver. This code is used
on the EtherNAT adapter card for the Atari Falcon extension port.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Tested-by: Christian Steigies <cts@debian.org>
[geert: Sort Kconfig entries, split in hard and soft dependencies]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's a big pile of changes for this round.
We have
* a lot of regulatory code changes to deal with the
way newer Intel devices handle this
* a change to drop packets while disconnecting from
an AP instead of trying to wait for them
* a new attempt at improving the tailroom accounting
to not kick in too much for performance reasons
* improvements in wireless link statistics
* many other small improvements and small fixes that
didn't seem necessary for 3.19 (e.g. in hwsim which
is testing only code)
Conflicts:
drivers/staging/rtl8723au/os_dep/ioctl_cfg80211.c
Minor overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves on previously added support for ipv6 addresses. The code
is consolidated to a single file and adds an api for use by dependent upper
level drivers such as cxgb4i/iw_cxgb4 etc.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Deepak Singh <deepak.s@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "unsigned long" by "u32" when handling 32-bit register data.
A.o., this saves 11 * 36 bytes in the static sh_eth_cpu_data structures
when compiling for 64-bit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
In boards, the dm9000 chip's power and reset can be controlled by gpio.
It makes sense to add them to the dm9000 driver and let dt be used to
enable power and reset the phy.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A VXLAN net_device looking for an appropriate socket may only consider
a socket which has a matching set of flags/extensions enabled. If
incompatible flags are enabled, return a conflict to have the caller
create a distinct socket with distinct port.
The OVS VXLAN port is kept unaware of extensions at this point.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements supports for the Group Policy VXLAN extension [0] to provide
a lightweight and simple security label mechanism across network peers
based on VXLAN. The security context and associated metadata is mapped
to/from skb->mark. This allows further mapping to a SELinux context
using SECMARK, to implement ACLs directly with nftables, iptables, OVS,
tc, etc.
The group membership is defined by the lower 16 bits of skb->mark, the
upper 16 bits are used for flags.
SELinux allows to manage label to secure local resources. However,
distributed applications require ACLs to implemented across hosts. This
is typically achieved by matching on L2-L4 fields to identify the
original sending host and process on the receiver. On top of that,
netlabel and specifically CIPSO [1] allow to map security contexts to
universal labels. However, netlabel and CIPSO are relatively complex.
This patch provides a lightweight alternative for overlay network
environments with a trusted underlay. No additional control protocol
is required.
Host 1: Host 2:
Group A Group B Group B Group A
+-----+ +-------------+ +-------+ +-----+
| lxc | | SELinux CTX | | httpd | | VM |
+--+--+ +--+----------+ +---+---+ +--+--+
\---+---/ \----+---/
| |
+---+---+ +---+---+
| vxlan | | vxlan |
+---+---+ +---+---+
+------------------------------+
Backwards compatibility:
A VXLAN-GBP socket can receive standard VXLAN frames and will assign
the default group 0x0000 to such frames. A Linux VXLAN socket will
drop VXLAN-GBP frames. The extension is therefore disabled by default
and needs to be specifically enabled:
ip link add [...] type vxlan [...] gbp
In a mixed environment with VXLAN and VXLAN-GBP sockets, the GBP socket
must run on a separate port number.
Examples:
iptables:
host1# iptables -I OUTPUT -m owner --uid-owner 101 -j MARK --set-mark 0x200
host2# iptables -I INPUT -m mark --mark 0x200 -j DROP
OVS:
# ovs-ofctl add-flow br0 'in_port=1,actions=load:0x200->NXM_NX_TUN_GBP_ID[],NORMAL'
# ovs-ofctl add-flow br0 'in_port=2,tun_gbp_id=0x200,actions=drop'
[0] https://tools.ietf.org/html/draft-smith-vxlan-group-policy
[1] http://lwn.net/Articles/204905/
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/xen-netfront.c
Minor overlapping changes in xen-netfront.c, mostly to do
with some buffer management changes alongside the split
of stats into TX and RX.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tg3_reset_task() uses only tp->lock for synchronizing with code
paths like tg3_open() etc. But since tp->lock is released before doing
synchronize_irq(), rtnl_lock should be taken in tg3_reset_task() to
synchronize it with other code paths.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to avoid the race between tg3_timer() and the execution paths
which does not invoke tg3_timer_stop() and releases tp->lock before
calling synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is fixing a race condition that may cause setting
count_pending to -1, which results in unwanted big bulk of arp messages
(in case of "notify peers").
Consider following scenario:
count_pending == 2
CPU0 CPU1
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 1)
schedule_delayed_work
team_notify_peers
atomic_add (adding 1 to count_pending)
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 1)
schedule_delayed_work
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 0)
schedule_delayed_work
team_notify_peers_work
atomic_dec_and_test (dec count_pending to -1)
Fix this race by using atomic_dec_if_positive - that will prevent
count_pending running under 0.
Fixes: fc423ff00d ("team: add peer notification")
Fixes: 492b200efd ("team: add support for sending multicast rejoins")
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds FCoE config option I40E_FCOE, so that FCoE can be enabled
as needed but otherwise have it disabled by default.
This also eliminate multiple FCoE config checks, instead now just
one config check for CONFIG_I40E_FCOE.
The I40E FCoE was added with 3.17 kernel and therefore this patch
shall be applied to stable 3.17 kernel also.
CC: <stable@vger.kernel.org>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for remote checksum offload in VXLAN. This uses a
reserved bit to indicate that RCO is being done, and uses the low order
reserved eight bits of the VNI to hold the start and offset values in a
compressed manner.
Start is encoded in the low order seven bits of VNI. This is start >> 1
so that the checksum start offset is 0-254 using even values only.
Checksum offset (transport checksum field) is indicated in the high
order bit in the low order byte of the VNI. If the bit is set, the
checksum field is for UDP (so offset = start + 6), else checksum
field is for TCP (so offset = start + 16). Only TCP and UDP are
supported in this implementation.
Remote checksum offload for VXLAN is described in:
https://tools.ietf.org/html/draft-herbert-vxlan-rco-00
Tested by running 200 TCP_STREAM connections with VXLAN (over IPv4).
With UDP checksums and Remote Checksum Offload
IPv4
Client
11.84% CPU utilization
Server
12.96% CPU utilization
9197 Mbps
IPv6
Client
12.46% CPU utilization
Server
14.48% CPU utilization
8963 Mbps
With UDP checksums, no remote checksum offload
IPv4
Client
15.67% CPU utilization
Server
14.83% CPU utilization
9094 Mbps
IPv6
Client
16.21% CPU utilization
Server
14.32% CPU utilization
9058 Mbps
No UDP checksums
IPv4
Client
15.03% CPU utilization
Server
23.09% CPU utilization
9089 Mbps
IPv6
Client
16.18% CPU utilization
Server
26.57% CPU utilization
8954 Mbps
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces udp_offload_callbacks which has the same
GRO functions (but not a GSO function) as offload_callbacks,
except there is an argument to a udp_offload struct passed to
gro_receive and gro_complete functions. This additional argument
can be used to retrieve the per port structure of the encapsulation
for use in gro processing (mostly by doing container_of on the
structure).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace tasklet with NAPI.
Add rx_queue to queue the remaining rx packets if the number of the
rx packets is more than the request from poll().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support Hisilicon hip04 ethernet driver, including 100M / 1000M controller.
The controller has no tx done interrupt, reclaim xmitted buffer in the poll.
v13: Fix the problem of alignment parameters for function and checkpatch warming.
v12: According Alex's suggestion, modify the changelog and add MODULE_DEVICE_TABLE
for hip04 ethernet.
v11: Add ethtool support for tx coalecse getting and setting, the xmit_more
is not supported for this patch, but I think it could work for hip04,
will support it later after some tests for performance better.
Here are some performance test results by ping and iperf(add tx_coalesce_frames/users),
it looks that the performance and latency is more better by tx_coalesce_frames/usecs.
- Before:
$ ping 192.168.1.1 ...
=== 192.168.1.1 ping statistics ===
24 packets transmitted, 24 received, 0% packet loss, time 22999ms
rtt min/avg/max/mdev = 0.180/0.202/0.403/0.043 ms
$ iperf -c 192.168.1.1 ...
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 1.0 sec 115 MBytes 945 Mbits/sec
- After:
$ ping 192.168.1.1 ...
=== 192.168.1.1 ping statistics ===
24 packets transmitted, 24 received, 0% packet loss, time 22999ms
rtt min/avg/max/mdev = 0.178/0.190/0.380/0.041 ms
$ iperf -c 192.168.1.1 ...
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 1.0 sec 115 MBytes 965 Mbits/sec
v10: According David Miller and Arnd Bergmann's suggestion, add some modification
for v9 version
- drop the workqueue
- batch cleanup based on tx_coalesce_frames/usecs for better throughput
- use a reasonable default tx timeout (200us, could be shorted
based on measurements) with a range timer
- fix napi poll function return value
- use a lockless queue for cleanup
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On i.MX28, the MDIO bus is shared between the two FEC instances.
The driver makes sure that the second FEC uses the MDIO bus of the
first FEC. This is done conditionally if FEC_QUIRK_ENET_MAC is set.
However, in newer designs, such as Vybrid or i.MX6SX, each FEC MAC
has its own MDIO bus. Simply removing the quirk FEC_QUIRK_ENET_MAC
is not an option since other logic, triggered by this quirk, is
still needed.
Furthermore, there are board designs which use the same MDIO bus
for both PHY's even though the second bus would be available on the
SoC side. Such layout are popular since it saves pins on SoC side.
Due to the above quirk, those boards currently do work fine. The
boards in the mainline tree with such a layout are:
- Freescale Vybrid Tower with TWR-SER2 (vf610-twr.dts)
- Freescale i.MX6 SoloX SDB Board (imx6sx-sdb.dts)
This patch adds a new quirk FEC_QUIRK_SINGLE_MDIO for i.MX28, which
makes sure that the MDIO bus of the first FEC is used in any case.
However, the boards above do have a SoC with a MDIO bus for each FEC
instance. But the PHY's are not connected in a 1:1 configuration. A
proper device tree description is needed to allow the driver to
figure out where to find its PHY. This patch fixes that shortcoming
by adding a MDIO bus child node to the first FEC instance, along
with the two PHY's on that bus, and making use of the phy-handle
property to add a reference to the PHY's.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently `ethtool -S` simply returns "no stats available". It
would be more useful to see what the various ethtool statistics
registers' values are. This change implements get_ethtool_stats,
get_strings, and get_sset_count functions to accomplish this.
Read all GEM statistics registers and sum them into
macb.ethtool_stats. Add the necessary infrastructure to make this
accessible via `ethtool -S`.
Update gem_update_stats to utilize ethtool_stats.
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is to help improve at-a-glace knowledge of the purpose of the
various Cadence MACB/GEM registers. Comments are more helpful for human
readability than short acronyms.
Describe various #define varibles Cadence MACB/GEM registers as documented
in Xilinix's "Zynq-7000 All Programmable SoC TechnicalReference Manual, v1.9.1
(UG-585)"
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate all the duplicate code for making Tx requests by
consolidating them into a single xennet_make_one_txreq() function.
xennet_make_one_txreq() and xennet_make_txreqs() work with pages and
offsets so it will be easier to make netfront handle highmem frags in
the future.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A function to count the number of slots an skb needs is more useful
than one that counts the slots needed for only the frags.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the rx packet length check in the sunvnet driver to allow
for a TSO max packet length greater than the LDC channel negotiated MTU.
These are negotiated separately and there is no requirement that
port->tsolen be less than port->rmtu, but if it isn't, it'll drop packets
with rx length errors.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netfront the Rx and Tx path are independent and use different
locks. The Tx lock is held with hard irqs disabled, but Rx lock is
held with only BH disabled. Since both sides use the same stats lock,
a deadlock may occur.
[ INFO: possible irq lock inversion dependency detected ]
3.16.2 #16 Not tainted
---------------------------------------------------------
swapper/0/0 just changed the state of lock:
(&(&queue->tx_lock)->rlock){-.....}, at: [<c03adec8>]
xennet_tx_interrupt+0x14/0x34
but this lock took another, HARDIRQ-unsafe lock in the past:
(&stat->syncp.seq#2){+.-...}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&stat->syncp.seq#2);
local_irq_disable();
lock(&(&queue->tx_lock)->rlock);
lock(&stat->syncp.seq#2);
<Interrupt>
lock(&(&queue->tx_lock)->rlock);
Using separate locks for the Rx and Tx stats fixes this deadlock.
Reported-by: Dmitry Piotrovsky <piotrovskydmitry@gmail.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx5 driver passes a string pointer in through a 'u64' variable,
which on 32-bit machines causes a build warning:
drivers/net/ethernet/mellanox/mlx5/core/debugfs.c: In function 'qp_read_field':
drivers/net/ethernet/mellanox/mlx5/core/debugfs.c:303:11: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
The code is in fact safe, so we can shut up the warning by adding
extra type casts.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rocker driver tries to assign a pointer to a 64-bit integer
and then back to a pointer. This is safe on all architectures,
but causes a compiler warning when pointers are shorter than
64-bit:
rocker/rocker.c: In function 'rocker_desc_cookie_ptr_get':
rocker/rocker.c:809:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
return (void *) desc_info->desc->cookie;
^
This adds another cast to uintptr_t to tell the compiler
that it's safe.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ALE table is a common resource for both the interfaces in Dual EMAC
mode and while bringing up the second interface in cpsw_ndo_set_rx_mode()
all the multicast entries added by the first interface is flushed out and
only second interface multicast addresses are added. Fixing this by
flushing multicast addresses based on dual EMAC port vlans which will not
affect the other emac port multicast addresses.
Fixes: d9ba8f9 (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing old hard-wired initialization code in the driver, which is no longer
used. Also deprecating few module parameters.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a bug in xgmac_mdio_read when clear the bit MDIO_STAT_ENC,
which '&' is missed in 'mdio_stat &= ~MDIO_STAT_ENC'.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 5ad24def21 ("cxgb4vf: Fix ethtool get_settings for VF driver")
mdio_addr of port_info structure was used unininitialzed. Fixing it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
