Error handling is on-its-head in this function. After invoking a function we
should examine the return code and return the error value if there was one.
Instead, this function checks for success and goes onto provide functionality
if success was received. Not so bad in a simple function like this, but in
a more complex one this could end up drowning in curly brackets.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AB8500 debugfs driver allocates memory to contain the name of a new sysfs
entry, but fails to apply the proper post-allocation checks. If the device
were to run out of memory, the allocation would return NULL. Without the
correct checks the driver will continue to populate address NULL with the
specified device name which would obviously cause a pointer dereference Oops.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AB8500 debugfs driver allocates memory for a new sysfs entry, but
fails to apply the proper post-allocation checks. If the device were to
run out of memory, the allocation would return NULL. Without the correct
checks the driver will continue to populate NULL->[show|store|...],
which would obviously cause a pointer dereference Oops.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Silences the following warning:
drivers/mfd/db8500-prcmu.c:2322:25: warning:
non-ANSI function declaration of function 'prcmu_ac_sleep_req'
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
User pass platform data to device, and platform data may be
NULL. Add the check for pdata.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
User pass platform data to device, and platform data may be
NULL. Add the check for pdata.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rather then open coding a cache of the vibra control registers use the
regmap cache code. Also cache the interrupt mask register, providing
a small performance improvement for the interrupt code.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This will be used to support refactoring of the ASoC CODEC driver to use
a regmap.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
These functions are not referenced anywhere, nor prototyped, so just
remove them.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If switching voltage fails, SD_CLK toggle enable bit should been cleared
so that SD host can control SD clock automatically.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The default phase can meet most cards' requirement, but it is not the
optimal one. In some extreme situation, the rx phase point produced by
the following tuning process will drift quite a distance.
Before tuning UHS card, this patch will set a more proper initial tx
phase point, which is calculated from statistic data, and can achieve
a much better tx signal quality.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Set a bit to enable rts5227 and rts5249 to enter a deeper internal
power-saving mode in S3, and recover it after resuming.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Clear hw_pfm_en to disable hardware PFM mode, to fix a bug that in some
situation registers in 0xFDxx domain can't be accessed.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
These actions are individual for each reader model, so should be put in
extra_init_hw instead of rtsx_pci_init_hw.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some actions to clear power state should be handled in .shutdown
callback in rtsx_pci_driver. This patch adopts the following measures to
catch this goal:
1. Add a function rtsx_pci_power_off to abstract the common ops in
.shutdown and .suspend
2. Add pcr->ops->force_power_down to fulfill the individual action for
each reader model
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Normally OEMs will set vendor setting to the config space of Realtek
card reader in BIOS stage. This patch reads the setting at the first,
and configure the internal registers according to it, to improve card
reader's compatibility condition.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Create "struct twl6030_irq" and place all local variables inside it.
Also allocate twl6030_irq structure dynamically during initialization.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since the TWL6030 PMIC is used with OMAP4 SoCs only and OMAP4 legacy
boot is dropped there are no needs to allocate the range of IRQ
descriptors during system boot to support TWL6030 IRQs.
Hence, convert it to use linear irq_domain and move IRQ configuration in
.map()/.unmap() callbacks of irq_domain. So, IRQ mapping and descriptors
allocation will be performed dynamically basing on DT configuration.
The error message will be reported in case if unmapped IRQ is received by
TWL6030 (virq==0).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add a missed check for errors when TWL IRQs are masked
initially on probe and report an error in case of failure.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
1) Removed request_irq() and replaced it with request_threaded_irq().
2) Removed generic_handle_irq() and replaced it with
handle_nested_irq().
Handling of these interrupts is nested, as we are handling an
interrupt (for e.g rtc, mmc1) when we are still servicing TWL irq.
3) Removed I2C read-retry logic for the case when twl_i2c_read() is
failed inside IRQ handler - there is no sense to do that, so just report
an error and return.
4) Each nested IRQ is configured with corresponding parent_irq,
which need to be retriggered in case if nested IRQ is marked
as IRQS_PENDING.
Signed-off-by: Naga Venkata Srikanth V <vnv.srikanth@samsung.com>
Signed-off-by: Oleg_Kosheliev <oleg.kosheliev@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Include <linux/module.h> in order to fix the following errors.
drivers/mfd/pm8921-core.c:209:16: error: expected declaration specifiers or '...' before string constant
drivers/mfd/pm8921-core.c:210:20: error: expected declaration specifiers or '...' before string constant
drivers/mfd/pm8921-core.c:211:16: error: expected declaration specifiers or '...' before string constant
drivers/mfd/pm8921-core.c:212:14: error: expected declaration specifiers or '...' before string constant
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some of Palmas resources like clock, SMPSs, LDOs etc can be controlled
by external pins ENABLE1, ENABLE2 or NSLEEP.
Add support to configure these resources to externally controlled.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds a regmap irqchip for DA9063 IRQs. It depends on
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap.git tags/regmap-irq-ack-mask
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is MFD module providing access to registers and interrupts of DA906x
series PMIC. It is used by other functional modules, registered as MFD cells.
Driver uses regmap with paging to access extended register list. Register map
is divided into two pages, where the second page is used during initialisation.
This module provides support to following functional cells:
- Regulators
- RTC
- HWMON
- OnKey (power key misc input device)
- Vibration (force-feedback input device)
- Watchdog
- LEDs
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds register definitions for the DA9063 PMIC. They will be used
by the following DA9063 mfd core driver and functional module drivers.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
regmap: Support for acknowledging masked IRQs
Some devices need interrupts to be clear when they are masked otherwise
the interrupt is not deasserted by the mask being set - add support for
this to regmap-irq from Philipp Zabel.
The reg_cache variable should be updated with current
steps in the reg_se register. Then the mask should
apply and clear the register. Previously, the reg_cache
can be an old redundant value that isn't updated.
Signed-off-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The child device intends to perform DMA operations then it needs a dma
mask and params set. This patches copies them from the parent device.
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Holger Dengler <dengler@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is no need to use a per CPU workqueue to poll, especially with the
5s delay used, so allow the scheduler to use any CPU.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Hook up "pm_power_off" to palmas power off routine if there is DT
property "ti,system-power-controller" defined, so platform which is
powered by this regulator can be powered off properly.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mallikarjun Kasoju <mkasoju@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
