In preparation for device tree, this patch changes how the DSI pins are
configured. The current configuration method is only doable with board
files and the configuration data is OMAP specific.
This patch moves the configuration data to the panel's platform data,
and the data can easily be given via DT in the future. The configuration
data format is also changed to a generic one which should be suitable
for all platforms.
The new format is an array of pin numbers, where the array items start
from clock + and -, then data1 + and -, and so on. For example:
{
0, // pin num for clock lane +
1, // pin num for clock lane -
2, // pin num for data1 lane +
3, // pin num for data1 lane -
...
}
The pin numbers are translated by the DSI driver and used to configure
the hardware appropriately.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The reset GPIO for Taal panel driver is currently requested in the
4430sdp board file. This patch moves the gpio request/free into the Taal
driver, where it should be.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Now that the tfp410 driver has been renamed in the code, this patch
finishes the renaming by renaming the files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The driver for the TFP410 DPI-to-DVI chip was named quite badly as "DVI
panel driver". This patch renames the code to use tfp410 name for the
driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Now that the panel-dvi driver handles the PD (power-down) GPIO, we can
remove the custom PD handling from the board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
'TIF_RUNLATCH' is already dropped from
commit fe1952fc0a
powerpc: Rework runlatch code
So '_TIF_RUNLATCH' should be removed as well.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
platform_device pdev can be NULL if CONFIG_MMC_OMAP_HS is not set.
Add check for NULL pointer. while at it move the duplicated functions
to omap4-common.c
Fixes the following boot crash seen with omap4sdp and omap4panda
when MMC is disabled.
Unable to handle kernel NULL pointer dereference at virtual address 0000008c
pgd = c0004000
[0000008c] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 Not tainted (3.4.0-rc1-05971-ga4dfa82 #4)
PC is at omap_4430sdp_init+0x184/0x410
LR is at device_add+0x1a0/0x664
Signed-off-by: Balaji T K <balajitk@ti.com>
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
SX1 board requirese i2c, so select it in Kconfig, otherwise I have the
following build error:
arch/arm/mach-omap1/board-sx1.c: In function 'sx1_i2c_write_byte':
arch/arm/mach-omap1/board-sx1.c:58:2: error: implicit declaration of function 'i2c_get_adapter' [-Werror=implicit-function-declaration]
arch/arm/mach-omap1/board-sx1.c:58:7: warning: assignment makes pointer from integer without a cast [enabled by default]
arch/arm/mach-omap1/board-sx1.c:67:2: error: implicit declaration of function 'i2c_transfer' [-Werror=implicit-function-declaration]
arch/arm/mach-omap1/board-sx1.c:68:2: error: implicit declaration of function 'i2c_put_adapter' [-Werror=implicit-function-declaration]
arch/arm/mach-omap1/board-sx1.c: In function 'sx1_i2c_read_byte':
arch/arm/mach-omap1/board-sx1.c:82:7: warning: assignment makes pointer from integer without a cast [enabled by default]
cc1: some warnings being treated as errors
make[1]: *** [arch/arm/mach-omap1/board-sx1.o] Error 1
make: *** [arch/arm/mach-omap1] Error 2
make: *** Waiting for unfinished jobs....
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If dtb is provided the needed device will be created dynamically.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If dtb is provided the needed device will be created dynamically.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Alignment was the last user of the ENABLE_INTS macro, which we can
now remove. All non-syscall exceptions now disable interrupts on
entry, they get re-enabled conditionally from C code. Don't
unconditionally re-enable in program check either, check the
original context.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We had a case where we could turn on hard interrupts while
leaving the PACA_IRQ_HARD_DIS bit set in the PACA. This can
in turn cause a BUG_ON() to hit in __check_irq_replay() due
to interrupt state getting out of sync.
The assembly code was also way too convoluted. Instead, we
now leave it to the C code to do the right thing which ends
up being smaller and more readable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a varient of the basic clk-gate code. This variant calls a
function before gating the clock off. This function is used to disable
the SATA or PCIe PHY.
Now that all the drivers prepare and enable there clk as needed, there
is no need for the common code to keep track of which clocks need
gating on. Let the common clock framework turn off clocks which are
not used.
Buy using the added clk varient, when the clk framework turns off SATA
or PCIe clocks, we also disabled SATA and PCIe PHYs which were not
needed.
The function kirkwood_pcie_id() can now be called outside of __init
code, so remove this property for it, and functions it calls.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Prepare and enable the clocks when the board indicates the pcie buses
will be used.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some orion platforms can gate the XOR driver clock. If the clock
exisits, unable/disable it as appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some orion platforms support gating of the clock. If the clock exists
enable/disbale it as appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some orion devices can gate the SDIO clock. If the clock exists,
enable/disable it as appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Not all orion platforms can gate the clock, but if it does exist,
enable/disable it as appropriate.
v2: Fix the name of the clkdev entry.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Not all platforms support gating the clock, so it is not an error if
the clock does not exist. However, if it does exist, we should
enable/disable it as appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The Orion kirkwood chips have a gatable clock per SATA channel. Add
code to get and enable this clk if it exists.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Let the machine pass to the platform which clock is used by the uart.
Enable the clock and use clk_get_rate() to determine its rate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Remove tclk from platform data. This makes the platform data
structure empty, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The t_clk is moved from the shared part of the ethernet driver into
the per port section. Each port can have its own gated clock, which it
needs to enable/disable, as oppossed to there being one clock shared
by all ports. In practice, only kirkwood supports this at the moment.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Remove now redundant tclk from SPI platform data. This makes the platform
data empty, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add tclk as a fixed rate clock for all platforms. In addition, on
kirkwood, add a gated clock for most of the clocks which can be gated.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
[mturquette@linaro.org: removed redundant CLKDEV_LOOKUP from Kconfig]
[mturquette@linaro.org: removed redundant clk.h from mach-dove/common.c]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Without runtime PM enabled, hwmod needs to leave all IP blocks in an
enabled state by default so any driver access to the HW will succeed.
This is accomplished by seting the postsetup_state to enabled for all
hwmods during init when runtime PM is disabled.
Currently, we have a special case for WDT in that its postsetup_state
is always set to disabled. This is done so that the WDT is disabled
and the timer is disarmed at boot in case there is no WDT driver.
This also means that when runtime PM is disabled, if a WDT driver *is*
built in the kernel, the kernel will crash on the first access to the
WDT hardware.
We can't simply leave the WDT module enabled, because the timer is
armed by default after reset. That means that if there is no WDT
driver initialzed or loaded before the timer expires, the kernel will
reboot.
To fix this, a custom reset method is added to the watchdog class of
omap_hwmod. This method will *always* disarm the timer after hwmod
reset. The WDT timer then will only be rearmed when/if the driver is
loaded for the WDT. With the timer disarmed by default, we no longer
need a special-case for the postsetup_state of WDT during init, so it
is removed.
Any platforms wishing to ensure the watchdog remains armed across the
entire boot boot can simply disable the reset-on-init feature of the
watchdog hwmod using omap_hwmod_no_setup_reset().
Tested on 3530/Overo, 4430/Panda.
NOTE: on 4430, the hwmod OCP reset does not seem to rearm the timer as
documented in the TRM (and what happens on OMAP3.) I noticed this
because testing the HWMOD_INIT_NO_RESET feature with no driver loaded,
I expected a reboot part way through the boot, but did not see a
reboot. Adding some debug to read the counter, I verified that right
after OCP softreset, the counter is not firing. After writing the
magic start sequence, the timer starts counting. This means that the
timer disarm sequence added here does not seem to be needed for 4430,
but is technically the correct way to ensure the timer is disarmed, so
it is left in for OMAP4.
Special thanks to Paul Walmsley for helping brainstorm ideas to fix
this problem.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[paul@pwsan.com: updated the omap2_wd_timer_reset() function in the
wake of commit 3c55c1baff ("ARM:
OMAP2+: hwmod: Revert "ARM: OMAP2+: hwmod: Make omap_hwmod_softreset
wait for reset status""); added kerneldoc; rolled in warning fix from Kevin]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Use 'common' as name for the common irq number in hwmod data for the McBSP
ports. The same name already in use for OMAP2430, and OMAP3.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Restore of context is not done for OMAP4. This patch
adds the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE in the OMAP4
hwmod data which activates the restore for OMAP4.
Currently the OMAP4 does not hit device off still the
driver may have support for it.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Wamsley <paul@pwsan.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Use 'common' as name for the common irq number in hwmod data for the McBSP
ports. The same name already in use for OMAP2430, and the OMAP4 hwmod data
will be using the same name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the HDQ1W hwmod for all OMAP2xxx devices.
Assume that OMAP2xxx chips have the same HDQ idle handling bug
as OMAP3:
http://www.spinics.net/lists/linux-omap/msg63576.html
and set the OCPIF_SWSUP_IDLE flag accordingly on the HDQ's OCP interface.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the HDQ1W hwmod for OMAP34xx, OMAP36xx, and AM3505/3517 devices.
According to the respective TRMs, it doesn't appear to be available for the
816x/814x or the AM335x.
The OCPIF_SWSUP_IDLE flag is added to work around an apparent hardware
bug: the hardware is not taking the CM_FCLKEN*_CORE.EN_HDQ bit into
account when considering whether to go idle:
http://www.spinics.net/lists/linux-omap/msg63576.html
This causes HDQ transfers to fail or become corrupt. Thanks to
NeilBrown for his help diagnosing and testing fixes for this problem.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Tested-by: NeilBrown <neilb@suse.de>
Much of the HDQ1W integration data is common between multiple generations
of OMAP SoCs, so rather than make several copies, we add it once into
files which are compiled for multiple SoCs.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Tested-by: NeilBrown <neilb@suse.de>
Implement a custom reset function for the HDQ1W IP block. This is
because the HDQ1W IP block, like I2C, has an internal clock gating bit
that needs to be toggled after setting the SOFTRESET bit to allow the
reset to propagate.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Avinash.H.M <avinashhm@ti.com>
Tested-by: NeilBrown <neilb@suse.de>
Add MMC for 2420 so we can pass the DMA request lines the same
way as we already do on omap2430 and later.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: updated to apply on top of the 3.5 hwmod cleanup;
changed mmc hwmod name/class to "msdi" as documented in the 2420 TRM Rev X;
added sysconfig register information; added 16 bit register width flag;
added MSDI custom reset code]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add extern func, "tegra_ahb_enable_smmu()" to inform AHB that SMMU is
ready.
Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra AHB Bus conforms to the AMBA Specification (Rev 2.0) Advanced
High-performance Bus (AHB) architecture.
The AHB Arbiter controls AHB bus master arbitration. This effectively
forms a second level of arbitration for access to the memory
controller through the AHB Slave Memory device. The AHB pre-fetch
logic can be configured to enhance performance for devices doing
sequential access. Each AHB master is assigned to either the high or
low priority bin. Both Tegra20/30 have this AHB bus.
Some of configuration params could be passed from DT too if needed.
Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Commit 554cdaefd1 ('ARM: orion5x: Refactor
mpp code to use common orion platform mpp.') seems to have accidentally
inverted the GPIO valid bits for MPP9 (only). For the mv2120 platform
which uses MPP9 as a GPIO LED device, this results in the error:
[ 12.711476] leds-gpio: probe of leds-gpio failed with error -22
Reported-by: Henry von Tresckow <hvontres@gmail.com>
References: http://bugs.debian.org/667446
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org [v3.0+]
Tested-by: Hans Henry von Tresckow <hvontres@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
