Otherwise we get:
`omap_system_dma_remove' referenced in section `.data' of arch/arm/plat-omap/built-in.o:
defined in discarded section `.devexit.text' of arch/arm/plat-omap/built-in.o
Signed-off-by: Tony Lindgren <tony@atomide.com>
Stephen Rothwell reported that the following commit broke the
linux-next build:
1fd36adcd9: Replace the fd_sets in struct fdtable with an array of unsigned longs
Fix places where ->fds_bits needed to be removed as the core
kernel no longer uses fd_set internally for file descriptor
table management. There are two places:
(1) drivers/staging/android/binder.c
(2) arch/mips/kernel/kspd.c
Question: Should sp_cleanup() in the MIPS arch be using find_next_bit()
or fls()?
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Ralf Bächle <ralf@linux-mips.org>
cc: Arve Hjønnevåg <arve@android.com>
Link: http://lkml.kernel.org/r/20120224105707.32170.11550.stgit@warthog.procyon.org.uk
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'vexpress-dt-v3.3-rc4' of git://git.linaro.org/people/pawelmoll/linux: (573 commits)
ARM: vexpress: Add Device Tree for V2P-CA15 core tile (TC1 variant)
ARM: vexpress: Add Device Tree for V2P-CA9 core tile
ARM: vexpress: Add Device Tree for V2P-CA5s core tile
ARM: vexpress: Motherboard RS1 memory map support
ARM: vexpress: Add Device Tree support
ARM: vexpress: Use FDT data in platform SMP calls
ARM: versatile: Map local timers using Device Tree when possible
ARM: vexpress: Get rid of MMIO_P2V
This adds full device tree boot support for the versatile express
platform, as has been awaited for a long time.
Conflicts:
arch/arm/mach-vexpress/core.h
The definition of AMBA_DEVICE was removed in one branch, and the
definition of MMIO_P2V was removed in the other branch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Convert the sa11x0 framebuffer driver to obtain the base address of its
hardware registers from the platform resources, and ioremap this rather
than relying on the static mappings.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is useful for testing RX handling of frames with bad
CRCs.
Requires driver support to actually put the packet on the
wire properly.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds Device Tree file for the CoreTile Express A15x2
(V2P-CA15) with Test Chip 1.
As the chip's GIC has 160 interrupt inputs and equivalent SMM
(FPGA) has GIC synthesised with 256 interrupts, NR_IRQS is
increased.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
This patch adds generic Versatile Express DT machine description,
Device Tree description for the motherboard and documentation for
the bindings.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Scan flatten device looking for A5/A9 SCU node and initialize
it using base address in "reg" property. If nothing is found,
assume that there is no special SCU initialization required
and initialize CPUs basing on numbers of "cpu" type devices
in "cpus" node of the Device Tree.
All this happens only if the board was booted with FDT,
otherwise ct_desc callbacks are used.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
So here's a boot tested patch on top of Jason's series that does
all the cleanups I talked about and turns jump labels into a
more intuitive to use facility. It should also address the
various misconceptions and confusions that surround jump labels.
Typical usage scenarios:
#include <linux/static_key.h>
struct static_key key = STATIC_KEY_INIT_TRUE;
if (static_key_false(&key))
do unlikely code
else
do likely code
Or:
if (static_key_true(&key))
do likely code
else
do unlikely code
The static key is modified via:
static_key_slow_inc(&key);
...
static_key_slow_dec(&key);
The 'slow' prefix makes it abundantly clear that this is an
expensive operation.
I've updated all in-kernel code to use this everywhere. Note
that I (intentionally) have not pushed through the rename
blindly through to the lowest levels: the actual jump-label
patching arch facility should be named like that, so we want to
decouple jump labels from the static-key facility a bit.
On non-jump-label enabled architectures static keys default to
likely()/unlikely() branches.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jason Baron <jbaron@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: a.p.zijlstra@chello.nl
Cc: mathieu.desnoyers@efficios.com
Cc: davem@davemloft.net
Cc: ddaney.cavm@gmail.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20120222085809.GA26397@elte.hu
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/arm/mach-shmobile/board-ag5evm.c: included 'linux/dma-mapping.h'
twice, remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the bit field width information for the IPSR4 register
in the r8a7779 pin function controller (PFC).
Without this fix the Marzen board fails to receive data
over the serial console due to misconfigured pin function
for the RX pin.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the sh73a0 SMP code to use 32-bit PSTR access.
This fixes wakeup from deep sleep for sh73a0 secondary CPUs.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The latest sh_eth driver needs a resource of TSU in the channel 1,
if the controller has TSU registers. So, this patch adds the resource.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Correct spelling "erorr" to "error" in
arch/sh/drivers/pci/pci-sh7780.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Everybody uses the generic pcibios_resource_to_bus() supplied by the core
now, so remove the ARCH_HAS_GENERIC_PCI_OFFSETS used during conversion.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: Chris Zankel <chris@zankel.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
N.B. Leon apparently never uses initial BAR values, so it didn't matter
that we never fixed up the I/O resources from bus address to CPU addresses.
Other sparc uses pci_of_scan_bus(), which sets device resources directly
to CPU addresses, not bus addresses, so it didn't need pcibios_fixup_bus()
either. But by telling the core about the offsets, we can nuke
pcibios_resource_to_bus().
CC: "David S. Miller" <davem@davemloft.net>
CC: sparclinux@vger.kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: linux-parisc@vger.kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: David Howells <dhowells@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
Here's the wrinkle on Cobalt: we can't generate normal I/O port addresses
on PCI because the GT-64111 doesn't do any address translation, so we have
this:
CPU I/O port addresses [io 0x0000-0xffffff]
PCI bus I/O port addresses [io 0x10000000-0x10ffffff]
Legacy-mode IDE controllers start out with the legacy bus addresses, e.g.,
0x1f0, assigned by pci_setup_device(). These are outside the range of
addresses GT-64111 can generate on PCI, but pcibios_fixup_device_resources()
converted them to CPU addresses anyway by adding io_offset. Therefore, we
had to pre-adjust them in cobalt_legacy_ide_fixup().
With io_offset = 0xf0000000, we had this:
res->start = 0x1f0 initialized in pci_setup_device()
res->start = 0x100001f0 -= io_offset in cobalt_legacy_ide_fixup()
res->start = 0x1f0 += io_offset in pcibios_fixup_device_resources()
The difference after this patch is that the generic pci_bus_to_resource()
only adds the offset if the bus address is inside a host bridge window.
Since 0x1f0 is not a valid bus address and is not inside any windows, it is
unaffected, so we now have this:
region->start = 0x1f0 initialized in pci_setup_device()
res->start = 0x1f0 no offset by pci_bus_to_resource()
That means we can remove both pcibios_fixup_device_resources() and
cobalt_legacy_ide_fixup().
I would *rather* set the host bridge offset to zero (which corresponds
to what the GT-64111 actually does), and have both CPU and PCI addresses
of [io 0x10000000-0x10ffffff]. However, that would require changes to
generic code that assumes legacy I/O addresses, such as pic1_io_resource
([io 0x0020-0x00021]), and we'd have to keep a Cobalt IDE fixup.
Of course, none of this changes the fact that references to I/O port
0x1f0 actually go to port 0x100001f0, not 0x1f0, on the Cobalt PCI bus.
Fortunately the VT82C586 IDE controller only decodes the low 24 address
bits, so it does work.
CC: Ralf Baechle <ralf@linux-mips.org>
CC: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: Michal Simek <monstr@monstr.eu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: Tony Luck <tony.luck@intel.com>
CC: Jack Steiner <steiner@sgi.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Convert from pci_scan_bus() to pci_scan_root_bus(). Supply the root
bus resources from bussoft. When we move the resource adjustment from
pcibios_fixup_resources() to the PCI core, it will be important to have
the root bus resources correct from the beginning.
CC: Tony Luck <tony.luck@intel.com>
CC: Jack Steiner <steiner@sgi.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: linux-alpha@vger.kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We already use pci_flags, so this just sets pci_flags directly and removes
the intermediate step of figuring out pci_probe_only, then using it to set
pci_flags.
The PCI core provides a pci_flags definition (currently __weak), so drop
the powerpc definitions in favor of that.
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_probe_only is set on ppc64 to prevent resource re-allocation
by the core. It's meant to be used in very specific circumstances
such as when operating under a hypervisor that may prevent such
re-allocation.
Instead of default to 1, we make it default to 0 and explicitly
set it in the few cases where we need it.
This fixes FSL PCI which wants it clear among others.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We never assign anything other than PCI_ASSIGN_ALL_BUSSES to pci_probe,
so just remove the indirection. If configurability is required in the
future, please use the pci_flags/PCI_REASSIGN_ALL_BUS functionality
as is done for powerpc.
CC: Ralf Baechle <ralf@linux-mips.org>
CC: linux-mips@linux-mips.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some architectures (alpha, mips, powerpc) have an arch-specific
"pci_probe_only" flag. Others use PCI_PROBE_ONLY in pci_flags for
the same purpose. This moves mips to the pci_flags approach so
generic code can use the same test across all architectures.
CC: Ralf Baechle <ralf@linux-mips.org>
CC: linux-mips@linux-mips.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_flags is initialized to zero and never modified (I think this was just
copied from powerpc). Therefore, "(pci_flags & XX)" is always false and
"!(pci_flags & XX)" is always true, and we can remove all references
to pci_flags.
CC: Michal Simek <monstr@monstr.eu>
CC: microblaze-uclinux@itee.uq.edu.au
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI core provides a pci_flags definition (currently __weak), so drop
the arm definition in favor of that.
We EXPORT_SYMBOL(pci_flags) as arm did previously. I'm dubious about
this: no other architecture exports it, and I didn't see any modules in
the tree that reference it.
CC: Rob Herring <rob.herring@calxeda.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: linux-arm-kernel@lists.infradead.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some architectures (alpha, mips, powerpc) have an arch-specific
"pci_probe_only" flag. Others use PCI_PROBE_ONLY in pci_flags for
the same purpose. This moves alpha to the pci_flags approach so
generic code can use the same test across all architectures.
CC: linux-alpha@vger.kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Traditionally the kernel has refused to setup EFI at all if there's been
a mismatch in 32/64-bit mode between EFI and the kernel.
On some platforms that boot natively through EFI (Chrome OS being one),
we still need to get at least some of the static data such as memory
configuration out of EFI. Runtime services aren't as critical, and
it's a significant amount of work to implement switching between the
operating modes to call between kernel and firmware for thise cases. So
I'm ignoring it for now.
v5:
* Fixed some printk strings based on feedback
* Renamed 32/64-bit specific types to not have _ prefix
* Fixed bug in printout of efi runtime disablement
v4:
* Some of the earlier cleanup was accidentally reverted by this patch, fixed.
* Reworded some messages to not have to line wrap printk strings
v3:
* Reorganized to a series of patches to make it easier to review, and
do some of the cleanups I had left out before.
v2:
* Added graceful error handling for 32-bit kernel that gets passed
EFI data above 4GB.
* Removed some warnings that were missed in first version.
Signed-off-by: Olof Johansson <olof@lixom.net>
Link: http://lkml.kernel.org/r/1329081869-20779-6-git-send-email-olof@lixom.net
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
It's not perfect, but way better than before. Mark efi_enabled as false in
case of error and at least stop dereferencing pointers that are known to
be invalid.
The only significant missing piece is the lack of undoing the
memblock_reserve of the memory that efi marks as in use. On the other
hand, it's not a large amount of memory, and leaving it unavailable for
system use should be the safer choice anyway.
Signed-off-by: Olof Johansson <olof@lixom.net>
Link: http://lkml.kernel.org/r/1329081869-20779-5-git-send-email-olof@lixom.net
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Break out some of the init steps into helper functions.
Only change to execution flow is the removal of the warning when the
kernel memdesc structure differ in size from what firmware specifies
since it's a bogus warning (it's a valid difference per spec).
v4:
* Removed memdesc warning as per above
Signed-off-by: Olof Johansson <olof@lixom.net>
Link: http://lkml.kernel.org/r/1329081869-20779-2-git-send-email-olof@lixom.net
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Otherwise we get:
arch/arm/mach-omap2/board-zoom-display.c:64: undefined reference to `twl_i2c_read_u8'
arch/arm/mach-omap2/board-zoom-display.c:65: undefined reference to `twl_i2c_read_u8'
arch/arm/mach-omap2/board-zoom-display.c:84: undefined reference to `twl_i2c_write_u8'
arch/arm/mach-omap2/board-zoom-display.c:86: undefined reference to `twl_i2c_write_u8'
arch/arm/mach-omap2/board-zoom-display.c:91: undefined reference to `twl_i2c_write_u8'
arch/arm/mach-omap2/board-zoom-display.c:92: undefined reference to `twl_i2c_write_u8'
arch/arm/mach-omap2/board-zoom-display.c:72: undefined reference to `twl_i2c_write_u8'
Signed-off-by: Tony Lindgren <tony@atomide.com>
