The Tegra PMC (Power Management Controller) interfaces with an external
PMU (Power Management Unit), and controls wake-up from sleep modes.
This initial binding is the bare minimum required to control the PMC's
inversion of the PMU's interrupt signal.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add complete bindings to instantiate and configure the codec and
top-level audio complex on all currently supported boards using the
Tegra+WM8903 audio driver.
On those boards, disable the I2S2 controller since it isn't used.
On boards not using the WM8903 codec, disable all the audio devices;
they can be re-enabled once the relevant codec and ASoC machine drivers
have been ported to device-tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This will allow the sound node to refer to the I2S controllers by name
when creating phandles.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Adjust the dma-channel property name to match the binding implemented by
the driver. The binding was implemented and documented in a
separate change to the ASoC tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Document binding, and add the node to tegra*.dtsi.
The driver isn't actually instantiated from this node yet, but the I2S
binding will rely on being able to refer to the APB DMA node using a
phandle.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Tegra30 GPIO controller has one more bank than Tegra20, and hence
has one more interrupt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
If the SG bit is set in MMUTR the page is accessible for all
userspace processes (ignoring the ASID). So a process might randomly
access a page from a different process which had a shared page
(from shared memory) in its context.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
We had problems accessing our NOR flash trough mtd. The system always got
stuck at attaching UBI using ubiattach if booted from NFS or after mounting
squashfs as rootfs directly from NOR flash.
After some testing of the new changes introduced from v3.2-rc1 to v3.2-rc7
we had to apply the following patch to get mtd working again.
[gerg: The problem was ultimately caused by allocated kernel pages not having
the shared (SG) bit set. Without the SG bit set the MMU will look for page
matches incorporating the ASID as well. Things like module regions allocated
using vmalloc would fault when other processes run. ]
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The return path from an exception was checking too many bits in the
thread_info->flags, and getting stuck calling do_signal(). There was
no work to do, we should only be checking the low 8 bits (as per comments
and definitions in arch/m68k/include/asm/thread_info.h).
This fixes the stuck process problem when using strace.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fixing a regression with the PMU MSRs when PMU virtualization is
disabled, a guest-internal DoS with the SYSCALL instruction, and a dirty
memory logging race that may cause live migration to fail.
* 'kvm-updates/3.3' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: do not #GP on perf MSR writes when vPMU is disabled
KVM: x86: fix missing checks in syscall emulation
KVM: x86: extend "struct x86_emulate_ops" with "get_cpuid"
KVM: Fix __set_bit() race in mark_page_dirty() during dirty logging
As the S3C24xx SoCs use the same rtc device a renaming capability like in
the adc driver is necessary.
This patch adds a s3c_rtc_setname function and names the rtc devices for
S3C2443 and S3C2416 accordingly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Especially the TICNT registers are different from the two rtc
types that currently exists.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
regs-rtc.h uses a mixture of tabs and spaces and also (x<<y)
to format bits. So, before adding new stuff clean up the formatting
and also add spaces to the bit definitions (i.e. (x << y) )
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
So that we can get the perf bench exec stack fixes and then apply the
remaining fix for the files added after what is in perf/urgent.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Some SoCs have a PCIe host controller to make it possible to attach
some other devices to it, like an other Wifi card.
This code was tested with an Netgear WNDR3400 (bcm4716 based), but
should work with all bcma based SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The power gpio for the external memory card was specified wrongly.
Replace it with the correct value (tested with warmboot with fastboot).
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Introduce some definitions for the tegra flow contoller. This will be
used by the code which controls entering and leaving LP3.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Initialize basic system clocks and provide a auxdata table to allow some
peripheral drivers to find their clocks.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Tegra30 has 1 extra legacy interrupt controller. Use the GIC ITLinesNumber
field to determine how many interrupt controllers we have and initialize
appropriately. Also make room for the extra tegra30 interrupts by moving
the GPIO IRQ base. This shouldn't affect existing code as it determines the
correct IRQ number for GPIOs using TEGRA_GPIO_TO_IRQ().
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'v3.3-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Correct M-5MOLS sensor clock frequency on Universal C210 board
ARM: EXYNOS: Correct framebuffer window size on Nuri board
ARM: SAMSUNG: Fix missing api-change from subsys_interface change
ARM: EXYNOS: Fix "warning: initialization from incompatible pointer type"
ARM: S5PV210: Fix the name of exynos4_clk_hdmiphy_ctrl() for S5PV210
ARM: EXYNOS: Remove build warning without enabling PM
ARM: SAMSUNG: Fix platform data setup for I2C adapter 0
ARM: EXYNOS: fix non-SMP builds for EXYNOS4
ARM: S3C6410: Use device names for both I2C clocks
ARM: S3C64XX: Make s3c64xx_init_uarts() static
Call runtime pm APIs pm_runtime_get_sync() and pm_runtime_put()
for enabling/disabling clocks appropriately. Remove syscore_ops and
instead use SET_RUNTIME_PM_OPS macro.
There is no more need to call omap_device_disable_idle_on_suspend
since driver is PM runtime adapted now.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In all OMAP1 SoCs, the MPUIO bank width is 16 bits. But, in OMAP7xx,
it is wrongly initialised to 32. Fix this.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The only bank->type (method) used in the OMAP GPIO driver is MPUIO type as they
need to be handled separately. Identify the same using a flag and remove all
METHOD_* macros.
mpuio_init() function is defined under #ifdefs. It is required only in case
of MPUIO bank type and only when PM operations are supported by it.
This is applicable only in case of OMAP16xx SoC's MPUIO GPIO bank type.
For all the other cases it is a dummy function. Hence clean up the same
and remove all the OMAP SoC specific #ifdefs.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
With register offsets now defined for respective OMAP versions we can get rid
of cpu_class_* checks. This function now has common initialization code for
all OMAP versions. Initialization specific to OMAP16xx has been moved within
omap16xx_gpio_init().
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Getting rid of ifdefs within the function by adding register offset intctrl
and associating OMAPXXXX_GPIO_INT_CONTROL in respective SoC specific files.
Also, use wkup_status register consistently instead of referring to wakeup
clear and wakeup set register offsets. Get rid of cpu_is_xxxx checks in
set_gpio_trigger() using irqctrl.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
It is not required to use hard-coded offsets any more in context save and
restore functions and instead use the generic offsets which have been correctly
initialized during device registration.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
By adding level and edge detection register offsets and then initializing them
correctly according to OMAP versions during device registrations we can now remove
lot of revision checks in these functions.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Wakeup enable register offset initialized according to OMAP versions
during device registration. Use this to avoid version checks.
Starting with OMAP4, legacy registers should not be used in combination
with the updated regsiters. Use wkup_en register consistently for
all SoCs wherever applicable.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove cpu-is checks while enabling/disabling OMAP GPIO module during a gpio
request/free.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Non-wakeup GPIOs are available only in OMAP2. Avoid cpu_is checks by making
non_wakeup_gpios as part of pdata.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Modify omap_gpio_prepare_for_idle() & omap_gpio_resume_after_idle() functions
to handle save context & restore context respectively in the OMAP GPIO driver
itself instead of calling these functions from pm specific files.
For this, in gpio_prepare_for_idle(), call *_get_context_loss_count() and in
gpio_resume_after_idle() call it again. If the count is different, do restore
context.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In omap3, save/restore context is implemented for GPIO banks 2-6 as GPIO bank1
is in wakeup domain. Instead of identifying bank's power domain by bank id,
use 'loses_context' flag which is filled by pwrdm_can_ever_lose_context()
during dev_init.
For getting the powerdomain pointer, omap_hwmod_get_pwrdm() is used.
omap_device_get_pwrdm() could not be used as the pwrdm information needs to be
filled in pdata, whereas omap_device_get_pwrdm() could be used only after
omap_device_build() call.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The gpio_bank_count is the count of number of GPIO devices in a SoC. Remove this
dependency from the driver by using list. Also remove the dependency on array of
pointers to gpio_bank struct of all GPIO devices.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Upstream commit d1fce9c115
"ARM: restart: bcmring: use new restart hook"
breaks building of this platform, since what used to be the
last field of the MACHINE_START/END block didn't have a
trailing comma. Once another field was added below, we get:
arch/arm/mach-bcmring/arch.c:198: error: request for member 'restart' in something not a structure or union
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove BCMRING DMA map code which is no longer used.
This also fixes a build error with dma.c introduced by
bfcd2ea6a4.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
i.MX SDMA: Fix burstsize settings
ARM: mach-shmobile: both USB DMAC instances on sh7372 are slave-only
dma: sh_dma: not all SH DMAC implementations support MEMCPY
at_hdmac: bugfix for enabling channel irq
dmaengine: fix missing 'cnt' in ?: in dmatest
