As Corey reported, the total_enabled and total_running times
could occasionally be 0, even though there were events counted.
It turns out this is because we record the times before reading
the counter while the latter updates the times.
This patch corrects that.
While looking at this code I found that there is a lot of
locking iffyness around, the following patches correct most of
that.
Reported-by: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20091120212508.685559857@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove a rcu_read_{,un}lock() pair and a few conditionals.
We can remove the rcu_read_lock() by increasing the scope of one
in the calling function.
We can do away with the system_state check if the machine still
boots after this patch (seems to be the case).
We can do away with the list_empty() check because the bare
list_for_each_entry_rcu() reduces to that now that we've removed
everything else.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20091120212508.606459548@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove a rcu_read_{,un}lock() pair and a few conditionals.
We can remove the rcu_read_lock() by increasing the scope of one
in the calling function.
We can do away with the system_state check if the machine still
boots after this patch (seems to be the case).
We can do away with the list_empty() check because the bare
list_for_each_entry_rcu() reduces to that now that we've removed
everything else.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20091120212508.527608793@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove a rcu_read_{,un}lock() pair and a few conditionals.
We can remove the rcu_read_lock() by increasing the scope of one
in the calling function.
We can do away with the system_state check if the machine still
boots after this patch (seems to be the case).
We can do away with the list_empty() check because the bare
list_for_each_entry_rcu() reduces to that now that we've removed
everything else.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20091120212508.452227115@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove a rcu_read_{,un}lock() pair and a few conditionals.
We can remove the rcu_read_lock() by increasing the scope of one
in the calling function.
We can do away with the system_state check if the machine still
boots after this patch (seems to be the case).
We can do away with the list_empty() check because the bare
list_for_each_entry_rcu() reduces to that now that we've removed
everything else.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20091120212508.378188589@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
E.g.:
[root@doppio linux-2.6-tip]# perf top -v --vmlinux
../build/tip/vmlinux > /dev/null build_id in vmlinux is
e96699725a47413a50c231864a8e7a8ced40a31b while expected is
18e7cc53db62a7d35e9d6f6c9ddc23017d38ee9a, ignoring it
I.e. perf top was told to use a vmlinux file that is not the one
currently running on the machine, it ignores it and falls back
to using /proc/kallsyms.
This solves many, at first, mysterious results when people have
a stale vmlinux file while keeping the default of trying to use
the vmlinux file in the current directory in things like 'perf
annotate' where the DWARF info is required and thus we can't use
just /proc/kallsyms.
Modules buildids are already being checked as of the previous
changeset in this series, because we are using the default
dso__load routine, that will look at a series of places looking
for the best file with a matching buildid, starting in the
-debuginfo directories.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1258757489-5978-5-git-send-email-acme@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Just like we do with the other DSOs. This also simplifies the
kernel_maps setup process, now all that the tools need to do is
to call kernel_maps__init and the maps for the modules and
kernel will be created, then, later, when
kernel_maps__find_symbol() is used, it will also call
maps__find_symbol that already checks if the symtab was loaded,
loading it if needed.
Now if one does 'perf top --hide_kernel_symbols' we won't pay
the price of loading the (many) symbols in /proc/kallsyms or
vmlinux.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1258757489-5978-4-git-send-email-acme@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In the kernel we have more than one notes section, so the linker
script combines all and puts them into a ".notes" combined
section. So we need to look at both sections and also traverse
them looking at multiple GElf_Nhdr entries till we find the one
we want, with the build_id.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1258757489-5978-2-git-send-email-acme@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It should just load kernel symbols, not load the list of
modules. There are more stuff to move to other routines, but
lets do it in several steps.
End goal is to be able to defer symbol table loading till we
find a hit for that map address range. So that the kernel &
modules are handled just like all the other DSOs in the system.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1258757489-5978-1-git-send-email-acme@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts:
arch/x86/kernel/kprobes.c
kernel/trace/Makefile
Merge reason: hw-breakpoints perf integration is looking
good in testing and in reviews, plus conflicts
are mounting up - so merge & resolve.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts:
tools/perf/util/symbol.c
Merge reason: this fix will get merged in .33, not .32, plus
resolve the conflict.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently shipping discard capable SSDs and arrays have rather sub-optimal
implementations of the command and can the use of it can cause massive
slowdowns. Make issueing these commands option as it's already in btrfs
and gfs2.
Signed-off-by: Christoph Hellwig <hch@lst.de>
[hirofumi@mail.parknet.co.jp: tweaks, and add "discard" to fat_show_options]
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Here is the final set of patches I used to get ffado to work with the
new firewire stack. With these patches, I was able to start ardour
and record from and playback to my PreSonus Inspire1394 from a
(mostly) Fedora 12 system.
Signed-off-by: Jay Fenlason <fenlason@redhat.com>
Until now, firewire-ohci exposed only the transmit cycle of the last
transmitted packet at each isochronous transmit complete event. This
made it impossible for FFADO (FireWire audio drivers in userspace) to
synchronize audio-out streams. The fix is to store the timestamp of
each packet in the iso xmit event. As a bonus, the transfer status is
stored too.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Reset the backoff delay when we reopen the connection, so that the delays
for any initial connection problems are reasonable. We were resetting only
after a successful handshake, which was of limited utility.
Signed-off-by: Sage Weil <sage@newdream.net>
Add basic support for the P4080 DS reference board. None of the data
path devices (ethernet, crypto, pme) are support at this time.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Re-write the code so its more standalone and fixed some issues:
* Bump'd # of CAM entries to 64 to support e500mc
* Make the code handle MAS7 properly
* Use pr_cont instead of creating a string as we go
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The max_size increase request to the MDS can get lost during an MDS
restart and reconnect. Reset our requested value after the MDS recovers,
so that any blocked writes will re-request a larger max_size upon waking.
Also, explicit wake session caps after the reconnect. Normally the cap
renewal catches this, but not in the cases where the caps didn't go stale
in the first place, which would leave writers waiting on max_size asleep.
Signed-off-by: Sage Weil <sage@newdream.net>
The mds map now uses the global_id as the 'key' (instead of the addr,
which was a poor choice).
This is protocol change.
Signed-off-by: Sage Weil <sage@newdream.net>
We may first learn our fsid from any of the mon, osd, or mds maps
(whichever the monitor sends first). Consolidate checks in a single
helper. Initialize the client debugfs entry then, since we need the
fsid (and global_id) for the directory name.
Also remove dead mount code.
Signed-off-by: Sage Weil <sage@newdream.net>
Please apply patch to update redboot section while firmware update. Code
checks if section needs to be updated before actually doing it.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use BIT for macro definitions wherever possible, remove
unused and redundant macros.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Summary of Changes:
-Fix to receive multicast packets by setting the corresponding hardware
bit during initialization.
-Fix to re-enable the interface [by interface up command(ifup)] while the
interface is down.
-Fix to be able to down the interface by passing the last parameter
correctly to request_irq().
-Remove to read 4 extra bytes from the receiving queue after reading a
packet, even though it does not cause a predictable issue now.
-Remove occurrences of transmission done interrupt in order to tx
throughput enhancement.
-Enable IP checksum for packet receiving by setting the corresponding
hardware bit during initialization.
-Relocate ks_enable_int()/ks_disable_int() in order not to declare those
functions at the beginning of the file.
-Rename ks_enable()/_disable() to ks_enable_qmu()/ks_disable_qmu() in
order to give more meaningful names and relocate them not declaire
those functions at the beginning of the file.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building for Sun 3:
drivers/net/ethoc.c:1091: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `ethoc_probe':
drivers/net/ethoc.c:965: undefined reference to `dma_alloc_coherent'
drivers/net/ethoc.c:1063: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring the OEM bits in the PHY on 82577/82578, do not restart
autonegotiation if the firmware is blocking it (e.g. when an IDE-R session
is active) because the link must not go down.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A workaround for pre-release versions of 82577 is causing link issues on
some switches. The workaround is no longer needed on production parts so
remove it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some devices (e.g. 82578) not having a Tx timeout factor when linked at
100Mbps can cause false reports of hardware hangs on busy hubs.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When flow control (pause) parameters were changed via ethtool (i.e. enabled
or disabled), the newly calculated thresholds were not being written to the
device for non-fiber media.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary workaround that mistakenly does not perform a page
select operation for PHY registers 29 and 30 (assuming these are the PHY
debug port address and data registers) on 82578 which can cause reads
of the Transmit with No Carrier Sense statistics register on page 778 to be
read from an incorrect page. Also error out if the page select operation
fails.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3ec2a2b80f broke Tx/Rx when using
jumbo frames on certain parts (i.e. only PAUSE frames could be exchanged
once the high water mark was reached preventing normal packet traffic).
This patch reverts the breakage and sets appropriate high and low water
marks of the Rx FIFO for 82577/82578 which require a workaround due to a
flow control issue in hardware.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide nop fscache_stat_d() macro if CONFIG_FSCACHE_STATS=n lest errors like
the following occur:
fs/fscache/cache.c: In function 'fscache_withdraw_cache':
fs/fscache/cache.c:386: error: implicit declaration of function 'fscache_stat_d'
fs/fscache/cache.c:386: error: 'fscache_n_cop_sync_cache' undeclared (first use in this function)
fs/fscache/cache.c:386: error: (Each undeclared identifier is reported only once
fs/fscache/cache.c:386: error: for each function it appears in.)
fs/fscache/cache.c:392: error: 'fscache_n_cop_dissociate_pages' undeclared (first use in this function)
Signed-off-by: David Howells <dhowells@redhat.com>
GFS2 has been altered to pass THIS_MODULE to slow_work_register_user(), but
hasn't been altered to #include <linux/module.h> to provide it, resulting in
the following error:
fs/gfs2/recovery.c:596: error: 'THIS_MODULE' undeclared here (not in a function)
Add the missing #include.
Signed-off-by: David Howells <dhowells@redhat.com>
As of the patch:
SLOW_WORK: Wait for outstanding work items belonging to a module to clear
Wait for outstanding slow work items belonging to a module to clear
when unregistering that module as a user of the facility. This
prevents the put_ref code of a work item from being taken away before
it returns.
slow_work_register_user() takes a module pointer as an argument. CIFS must now
pass THIS_MODULE as that argument, lest the following error be observed:
fs/cifs/cifsfs.c: In function 'init_cifs':
fs/cifs/cifsfs.c:1040: error: too few arguments to function 'slow_work_register_user'
Signed-off-by: David Howells <dhowells@redhat.com>
tc is required by CONFIG_IXGBE_DCB.
This also fixes compilation warning:
drivers/net/ixgbe/ixgbe_main.c: In function ‘ixgbe_tx_is_paused’:
drivers/net/ixgbe/ixgbe_main.c:245: warning: unused variable ‘tc’
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
