This is a commit that is shared with Kishon's phy repository.
* tag 'depends/phy-dt-header'
phy: Add PHY header file for DT x Driver defines
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Linux 3.18-rc4 is a dependency for the phy-dt-header branch that
is needed for the final mvebu DT changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "Second DT batch for 3.19" from Nicolas Ferre:
- some trivial fixes: macro for IRQ, license wording
- DMA description for sama5d4
- RTT as RTC driver definition plus associated GPBR for several SoCs
- addition of missing nodes: rtc for at91sam9rl, isi for at91sam9g45
* tag 'at91-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: at91sam9g45: add ISI node
ARM: at91/dt: enable the RTT block on the at91sam9m10g45ek board
ARM: at91/dt: enable the RTT block on the sam9g20ek board
ARM: at91/dt: add GPBR nodes
ARM: at91/dt: add RTT nodes to at91 dtsis
ARM: at91/dt: at91sam9rl: add rtc
ARM: at91: fix GPLv2 wording
ARM: at91/dt: sama5d4: add DMA support
ARM: at91/dt: sama5d4: use macro instead of numeric value
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "Broadcom Cygnus SoC Device Tree changes" from Florian Fainelli:
This pull request contains the Broadcom Cygnus Device Tree changes:
- binding documentation for the SoC and clock
- cygnus SoC and clock dtsi files
- DTS for Cygnus Entreprise phone, BCM911360K and BCM958300K
* tag 'arm-soc/for-3.19/cygnus-dts-v2' of http://github.com/brcm/linux:
ARM: dts: Enable Broadcom Cygnus SoC
dt-bindings: Document Broadcom Cygnus SoC and clocks
[arnd: something went wrong here, we already had pulled an earlier
version of the same patches, which had the wrong license statement.
I've pulled this one over the old pull request and fixed up the
conflicts now]
Conflicts:
arch/arm/boot/dts/bcm-cygnus-clock.dtsi
arch/arm/boot/dts/bcm-cygnus.dtsi
arch/arm/boot/dts/bcm911360_entphn.dts
arch/arm/boot/dts/bcm911360k.dts
arch/arm/boot/dts/bcm958300k.dts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch corrects the vendor-prefix for isl29028 in the compatible property from
"isil,isl29028" to "isl,isl29028" according to listed vendor-prefixes in
Documentation/devicetree/bindings/vendor-prefixes.txt. Incorrect vendor-prefix "isl"
was reported by checkpatch.pl warning for drivers/staging/iio/light/isl29028.c.
Thus incorrect vendor-prefix "isil" was corrected for every mention of device isl29028.
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds the correct vendor-prefix for device isl29028 and
maintains deprecated vendor-prefix found by checkpatch warning
for older kernel releases.
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch documents deprecated vendor name "isil" to fix warning of
undocumented string for device isl29028 as reported while running checkpatch.pl
on drivers/staging/iio/light/isl29028.c. This is done to maintain compatibility
with older kernels.
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch documents the device isl29028 with its vendor-prefix. Undocumented deprecated vendor-prefix
found by checkpatch also documented for compatibility reasons.
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The model B and B+ differ in the GPIO lines for ACT and PWR leds, and the
I2S interface.
Signed-off-by: Matthias Klein <matthias.klein@linux.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "Device tree related changes for omaps" from Tony Lindgren:
- Fix currently harmless but wrong sizes for various GPMC connected
devices
- Set up timings for several GPMC connected devices to get rid of
bootloader dependencies in later patches
- Enable various drivers for dra7xx
- Prepare Igep boards to support new variants
- Add intial support for BeagleBoard-X15
* tag 'omap-for-v3.19/dt-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (37 commits)
ARM: dts: DRA7: Add aliases for all serial ports
ARM: dts: Add am57xx-beagle-x15
ARM: OMAP2+: igep00x0: Add pdata-quirks for the btwilink device.
ARM: dts: omap3-igep00x0: Remove i2c2 node.
ARM: dts: omap3-igep0020-rev-f: Support IGEPv2 Rev. F
ARM: dts: omap3-igep0020-common: Introduce igep0020 common dtsi file.
ARM: dts: omap3-igep0030-rev-g: Support IGEP COM MODULE Rev. G
ARM: dts: omap3-igep0030-common: Introduce igep0030 common dtsi file.
ARM: dts: omap3-igep00x0: Move outside common file the on board Wifi module.
ARM: dts: omap3-igep0020: Specify IGEPv2 revision in device tree.
ARM: dts: omap3-igep0030: Specify IGEP COM revision in device tree.
ARM: dts: omap3-igep00x0: Move NAND configuration to a common place.
ARM: dts: omap3-igep00x0: Fix UART2 pins that aren't common.
ARM: dts: dra7: add labels to DWC3 nodes
ARM: dts: dra72x-evm: Enable CPSW and MDIO
ARM: dts: dra7-evm: Keep all VDD rails always-on
ARM: dts: dra72-evm: Add MMC nodes
ARM: dts: dra72-evm: Add power button node
ARM: dts: dra72-evm: Provide explicit pinmux for TPS PMIC
ARM: dts: dra72-evm: Add regulator information to USB2 PHYs
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "ARM: DT: Hisilicon terminal SoC HiX5HD2 DT updates for 3.19" from Wei Xu:
- Add reboot node, reusing syscon-reboot
- Add I2C nodes Hisilicon IP
- Add IR node based on Hisilicon IP
- Add Watchdog node based on ARM IP
- Add GPIO nodes based on ARM GPIO IP
- Add SATA node based on Hisilicon IP
- Add USB nodes
- Add MMC nodes based on Synopsys IP
- Add GMAC nodes based on Hisilicon IP
* tag 'hix5hd2-dt-for-3.19' of git://github.com/hisilicon/linux-hisi:
ARM: dts: hix5hd2: add reboot node
ARM: dts: hix5hd2: add i2c node
ARM: dts: hix5hd2: add ir node
ARM: dts: hix5hd2: add wdg node
ARM: dts: hix5hd2: add gpio node
ARM: dts: hix5hd2: add sata node
ARM: dts: hix5hd2: add usb node
ARM: dts: hix5hd2: add mmc node
ARM: dts: hix5hd2: add gmac node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "Third Round of Renesas ARM Based SoC DT Cleanups for v3.19" from Simon Horman:
* Use keyboard as gpio-keys node name
* tag 'renesas-dt-cleanups3-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: kzm9g-reference: Use keyboard as gpio-keys node name
ARM: shmobile: koelsch: Use keyboard as gpio-keys node name
ARM: shmobile: lager: Use keyboard as gpio-keys node name
ARM: shmobile: armadillo800eva: Use keyboard as gpio-keys node name
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the RTT and GPBR devices and specify the general purpose register
used to store the current time.
Enable wakeup on RTT event on the shutdown controller device.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
During the submission of these new sama5d4 files, the GPL notice mentioned the
device tree as a library, which is not really accurate.
Fix all these library mentions to reflect the fact that it's actually just a
file.
Reported-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
same issue as commit 7f5ae35536:
"Without DMA_PRIVATE the driver is not able to allocate more than one channel.
Since it uses dma_get_any_slave_channel that calls private_candidate, the
second allocation fails at
/* some channels are already publicly allocated */
"
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The total size of the transfer was wrong in at_xdmac_prep_slave_sg()
resulting in bad computation of the transfer residue by
at_xdmac_tx_status().
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
According to the Atmel eXtended DMA controller datasheet, requesting a
DMA transfer flush for a channel is only revelant when this transfer is
source peripheral synchronized.
So we have to check this condition before requesting a channel flush by
writing the channel bit into the Global channel SoftWare Flush (GSWF)
register then waiting for flush to complete by monitoring the end of
Flush Interrupt Status (FIS) bit in the Channel Interrupt Status (CIS)
register.
Indeed, for non source peripheral synchronized transfer, writing the
channel bit into the GSWF register does nothing. Especially, the FIS bit
is never set into the CIS register. The former code looped forever
waiting for this bit to be set.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
_relaxed version of readl and writel are not implemented on all
architecture so COMPILE_TEST has to be removed in order to not cause
some build failures.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As documented in printk-formats.txt the dma_addr_t should be printed with
%pad specfiers. This way it works on all archs.
make.cross ARCH=s390
All warnings:
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_slave_sg':
>> drivers/dma/at_xdmac.c:621:3: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
>> drivers/dma/at_xdmac.c:621:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
>> drivers/dma/at_xdmac.c:628:4: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_dma_cyclic':
>> drivers/dma/at_xdmac.c:663:2: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan), "%s: buf_addr=0x%08x, buf_len=%d, period_len=%d, dir=%s, flags=0x%lx\n",
^
>> drivers/dma/at_xdmac.c:690:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
>> drivers/dma/at_xdmac.c:709:3: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
>> drivers/dma/at_xdmac.c:709:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
>> drivers/dma/at_xdmac.c:716:4: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
>> drivers/dma/at_xdmac.c:731:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_dma_memcpy':
>> drivers/dma/at_xdmac.c:765:2: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan), "%s: src=0x%08x, dest=0x%08x, len=%d, flags=0x%lx\n",
^
>> drivers/dma/at_xdmac.c:765:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan), "%s: remaining_size=%u\n", __func__, remaining_size);
^
>> drivers/dma/at_xdmac.c:845:3: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
>> drivers/dma/at_xdmac.c:845:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
>> drivers/dma/at_xdmac.c:852:4: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
drivers/dma/at_xdmac.c: In function 'at_xdmac_tx_status':
>> drivers/dma/at_xdmac.c:929:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As documented in printk-formats.txt the size_t should be printed with
%zu/%zd specfiers. This way it works on all archs.
make.cross ARCH=avr32
All warnings:
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_dma_cyclic':
>> drivers/dma/at_xdmac.c:663: warning: format '%d' expects type 'int', but argument 6 has type 'size_t'
>> drivers/dma/at_xdmac.c:663: warning: format '%d' expects type 'int', but argument 7 has type 'size_t'
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_dma_memcpy':
>> drivers/dma/at_xdmac.c:765: warning: format '%d' expects type 'int', but argument 7 has type 'size_t'
>> drivers/dma/at_xdmac.c:794: warning: format '%u' expects type 'unsigned int', but argument 5 has type 'size_t'
>> drivers/dma/at_xdmac.c:815: warning: format '%u' expects type 'unsigned int', but argument 5 has type 'size_t'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This driver uses read_relaxed and writel_relaxed to read, write to IO
memory. the config defines COMPILE_TEST so gets compiled on different archs.
This causes issue as few archs like x86 etc don't define it.
So use readl/writel which is defined in all archs
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
BeagleBoard-X15 is the next generation Open Source Hardware
BeagleBoard based on TI's AM5728 SoC featuring dual core 1.5GHz A15
processor. The platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x1080@60), separate LCD
port, video In port, 4GB eMMC, uSD, Analog audio in/out, dual 1G
Ethernet.
For more information, refer to:
BeagleBoard-X15 Wiki:
http://www.elinux.org/Beagleboard:BeagleBoard-X15
AM5728 is part of the Sitara product family whose additional details
will be available: http://www.ti.com/lsds/ti/arm/overview.page
Technical Reference Manual for AM5728 is public domain at:
http://www.ti.com/lit/spruhz6
Just add basic support for the moment, the following updates are needed:
i) Ethernet - depends on SoC dts fixes
ii) USB Client (USB2) - depends on GPIO extcon
ii) HDMI - additional driver fixes pending
iii) Audio - additional driver fixes pending
NOTE:
AM5728 Data Manual (SPRS915L - August 2014) section 4.1.1 states: "All
unused power supply balls must be supplied with the voltages specified
in the Section 5.2, Recommended Operating Conditions". This implies
that all unused voltage rails for AM5728 can never be switched off even
if the hardware blocks inside that voltage domain is unused. Switching
off these unused rails may result in stability issues on other domains
and increased leakage and power-on-hour impacts.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add btwilink device for IGEPv2 Rev. F and IGEP COM MODULE Rev. G.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can't suppose that the i2c2 pins are configured as I2C bus, these pins are
connected to expansion connectors.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the new hardware revision of the IGEPv2. Basically, the new
revision F replaces the old Wifi module for a Wilink8 based module.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the omap3-igep0020-common.dtsi file and remove repeated parts leaving
the nodes that are not common between IGEPv2 hardware revisions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
